• Sections

  • Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Derek Cohen

    Dining room carver chairs - Take 2

    Thread Starter: Derek Cohen

    About a month ago I began a thread about designing and building two carver chairs to accompany the 6 bentwood chairs we have owned for the past 40 years. The chairs were purchased all those years ago along with a table, which is around 200 years old. We need a larger table, and time has come to...

    Last Post By: stephen thomas Yesterday, 3:07 PM Go to last post
    steven c newman

    Lumber supply

    Thread Starter: steven c newman

    Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..

    Last Post By: steven c newman Yesterday, 12:56 PM Go to last post
    Steve Mathews

    Itching to buy a new tool? What tools have you wasted money on?

    Thread Starter: Steve Mathews

    One of those sitting at the computer in the morning with a cup of coffee itching to buy a new tool ... So I come across this Veritas Scraper Burnisher for Turners and looked at a few videos reviews of it and thought why not. After reading a few reviews posted on this forum I later realized it was...

    Last Post By: stephen thomas Yesterday, 1:46 PM Go to last post
    Karl Card

    Help with low motor power on table saw

    Thread Starter: Karl Card

    Had a 7.5 baldor, had a seperate post on this because I thought I figured out what was going on but evidently this is beyond my knowledge or experience. I replaced caps on 7.5 baldor, no difference, bought new leeson 7.5 hp, both single phase motors, got it hooked up, check wiring, cranked...

    Last Post By: Rick Potter Yesterday, 11:31 PM Go to last post
    chris hood

    Router questions

    Thread Starter: chris hood

    My router on the recently purchased router table quit, it came on then off then on now it will not come on. I have it pulled apart trying to get all the sawdust out of the connections, it's embedded pretty bad, not sure if that is the cause but worth a try. I found another identical one on eBay for...

    Last Post By: Doug Garson Today, 12:14 AM Go to last post
    Nick Crivello

    Economics of milling vs store bought hardwoods?

    Thread Starter: Nick Crivello

    I'm pondering the economics of a mill vs buying rough lumber at retail/wholesale. In the Bay Area, depending on where you shop hardwoods like Oak and walnut can run up to $15-18bf/ft, or more for the rift/quarter sawn stuff. If one is able to source your own logs, running your own mil and kiln...

    Last Post By: Rod Sheridan Yesterday, 8:29 PM Go to last post

  • Recent Polls

    What are your thoughts? (Votes: 6)

    1. Been doing it like (or equivalent) this for years. (Votes: 4)

    2. Wow! Never thought of that. (Votes: 0)

    3. Been doing it with mirrors. (Votes: 2)

    4. Ain't got a boat, truck, care… (Votes: 0)

  • Recent Forum Posts

    Doug Garson

    Router questions

    That's the same switch I have on my router table with my Bosch 1617EVS. If the internal switch in the router ever acts up, i'll do the same.

    Doug Garson Today, 12:14 AM Go to last post
    dirk martin

    Carving Edges. Need Bit

    No.
    I'm looking to achieve something more like this:

    dirk martin Today, 12:08 AM Go to last post
    Rick Potter

    Help with low motor power on table saw

    Non electrician, and off the wall. Is it possible you are on two separate 120 breakers which are on the same leg at the panel?

    Ignore me

    Rick Potter Yesterday, 11:31 PM Go to last post
    Bill Dufour

    John Lincoln "Johnny" Clem

    The civil war ended in 1865. The last civil war widow died in 2020. Sometime in the 1970's a congress member tried to shut down the civil war veterans

    Bill Dufour Yesterday, 11:27 PM Go to last post
    Bill Dufour

    Getting a little exercise

    I put a little magnetic tool holder in the closet with the furnace/ac in the house. Keep a few basic tools there and return them when done. If I forget

    Bill Dufour Yesterday, 11:23 PM Go to last post

  • Recent Blog Posts