Sawmill Creek Woodworking Community - Powered by vBulletin
  • Register
  • Help

  • What's New?
  • Forum
  • Articles
    • The Sawmill Creek Press
  • Blogs
  • Donate
  • Sponsors
  • Friends of the Creek
  • Advanced Search
  • Home
  • Home
  • The Sawmill Creek Press


  1. If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
  • Sections

    • Sawmill Creek News
    • Workshops
    • Woodturning
    • Social Woodworking
    • Tools
      • Lathes and Accessories
      • Table Saws and Accessories
    • Jigs and Fixtures
    • Cabinetry
  • Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Dave Anderson NH

    Time for some levity

    Thread Starter: Dave Anderson NH

    With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.

    Last Post By: Kev Williams Today, 4:53 PM Go to last post
    Jack Hovanec

    Best 24” bandsaw for industrial setting?

    Thread Starter: Jack Hovanec

    Anyone here own any of these saws or have any gripes/good things to say about them? I have an old 36” crescent which is a well built machine but has a multitude of issues that aren’t worth it to me to fix. Looking at these smaller 24”ish saws to replace it. Primary uses resawing up to 8”...

    Last Post By: Mark Woodmark Today, 5:06 PM Go to last post
    John Goodin

    Thoughts on new Woodpeckers DP Pro Drill Press Fence

    Thread Starter: John Goodin

    Does anyone have experience or thoughts about the new woodpecker drill press fence? Basically it is hollow aluminum rectangle tube with with an opening in the center and attachment for a shop vac on the end. This allows the fence to be a conduit for dust collection. The link below also show the...

    Last Post By: Mike Goetzke Yesterday, 10:13 PM Go to last post
    Bob Riefer

    AWB workbench - a few options

    Thread Starter: Bob Riefer

    I have now read Chris S.'s Anarchist Workbench book (great read!!) and am ready to embark on the build. Overall, I plan to pretty much replicate what he suggests as his rationale throughout made sense to me based on how I've used my maple butcher block topped existing bench. But there are a...

    Last Post By: Jim Becker Today, 11:19 AM Go to last post
    Thomas Colson

    BORG or local wood supplier for cabinet plywood?

    Thread Starter: Thomas Colson

    Getting ready to do some wall cabinets, and I've got all my face frame and door parts milled and cut. Was going to start assembling carcasses this weekend when I happened to glance at plywood prices at the BORG :mad::mad::mad::mad::mad:!!!!!!! So the quality of BORG 3/4 plywood is pretty well known...

    Last Post By: Larry Frank Today, 9:52 AM Go to last post
    Scott Winners

    Leg vise experiences?

    Thread Starter: Scott Winners

    I just ordered from Lake Erie and Anchora Yacht Services, have a couple or four weeks to get my act together. My main questions regard the chop. I am seeing a lot of folks using 12/4 stock, but then trimming the top of the chop back to half an inch or so so they can get at the workpiece. ...

    Last Post By: Michael Bulatowicz Today, 9:54 AM Go to last post
  • Wally Dickerman

    Using CA Glue in Woodturning 

    by
    Wally Dickerman
    • View Profile
    • View Forum Posts
    • View Blog Entries
    • View Articles
    Published on 11-23-2014 7:59 AM

    There have been some recent threads on CA glue on the Turners forum. The following is an article I did for my turning club ...
    Read More Read More 5 Comments
  • Recent Polls

    Would you recommend WATCO Danish Oil as a good oil finish? (Votes: 29)

    1. Yes, I would (Votes: 27)

    2. No, I wouldn't (Votes: 2)

  • Recent Forum Posts

    Charles Grauer

    Need help Adding on to the bottom to craftsman style doors

    Passage doors. Sorry I over looked that “small detail”. They cut them off for some reason. He bought the doors at a recycle place

    Charles Grauer Today, 5:19 PM Go to last post
    Rob Luter

    Sliding table saw

    This thread compelled my to visit the Felder and SCM websites. And I thought Thomas Lie-Neilsen ran a crack house! I need to save more money for retirement

    Rob Luter Today, 5:17 PM Go to last post
    Michael Rollins

    Jet 14sfx wheel removal

    Yea, I haven’t had mine very long either, but I was cutting some duck call blanks and some epoxy in the middle wasn’t fully cured, so it gummed up my

    Michael Rollins Today, 5:17 PM Go to last post
    Robert D Evans

    Tell me your experience with G0766

    I had mine about 18 months and it's been a good one. I'm still happy with my purchase. With 22" of swing and 3 hp, I don't have to worry about

    Robert D Evans Today, 5:14 PM Go to last post
    Tim Best

    First real hand tool only project

    Quick update...

    Back at it again today for a brief period. I disassembled the carcass this morning to attempt to repair the cracked pin that

    Tim Best Today, 5:09 PM Go to last post
  • Recent Blog Posts

  • Contact Us
  • Sawmill Creek
  • Archive
  • Terms of Service
  • Top
All times are GMT -4. The time now is 5:23 PM.
Powered by vBulletin® Version 4.2.5
Copyright © 2021 vBulletin Solutions Inc. All rights reserved.