Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Dave Anderson NH Yesterday, 7:57 PM

Dining room carver chairs - Take 2
Thread Starter: Derek Cohen
About a month ago I began a thread about designing and building two carver chairs to accompany the 6 bentwood chairs we have owned for the past 40 years. The chairs were purchased all those years ago along with a table, which is around 200 years old. We need a larger table, and time has come to...
Last Post By: stephen thomas Today, 3:07 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Today, 12:56 PM

Itching to buy a new tool? What tools have you wasted money on?
Thread Starter: Steve Mathews
One of those sitting at the computer in the morning with a cup of coffee itching to buy a new tool ... So I come across this Veritas Scraper Burnisher for Turners and looked at a few videos reviews of it and thought why not. After reading a few reviews posted on this forum I later realized it was...
Last Post By: stephen thomas Today, 1:46 PM

Help with low motor power on table saw
Thread Starter: Karl Card
Had a 7.5 baldor, had a seperate post on this because I thought I figured out what was going on but evidently this is beyond my knowledge or experience. I replaced caps on 7.5 baldor, no difference, bought new leeson 7.5 hp, both single phase motors, got it hooked up, check wiring, cranked...
Last Post By: Dan Friedrichs Today, 5:12 PM

help needed to unbox and assemble Jointer and Table saw :) N. of McKinney Texas
Thread Starter: George Speed
:eek: too old and weak lol. well weak for sure! Cannot hurt to ask :) 6" jointer , Jet 50" cab saw..... fun huh. (no) well kind of. actually exciting! Friday or Sat or Sun ? I might be able to get a neighbor to help, but they are often very busy. I am in Van Alstyne. Beer Pizza $ ?
Last Post By: Jim Koepke Today, 1:32 AM

Ken Glass

There is no available content written by Ken Glass

Recent Polls
What are your thoughts? (Votes: 6)

Been doing it like (or equivalent) this for years. (Votes: 4)

Wow! Never thought of that. (Votes: 0)

Been doing it with mirrors. (Votes: 2)

Ain't got a boat, truck, care… (Votes: 0)
Recent Forum Posts

What finishes over oil

Be nice to know if the tung oil was pure tung oil or polymerized tung oil which cures much faster and typically leaves a hard film finish.
Bill Howatt Today, 6:33 PM

Oilstones sharpening

I've never thinned any oil. It seems like a waste of time and effort to me. Once, in a bind with nothing, I used bacon grease and it worked fine. My
Tom M King Today, 6:22 PM

Ah,my kinda old Craftsman 14" Bandsaw.

Late 1990s machine is a survivor? I started woodworking in 1972, 1980s was about the time I stopped shopping at Sears. In the 1990s, they started doing
Richard Coers Today, 6:14 PM

Carving Edges. Need Bit

Can you clarify what the intention is?
Are you intending to carve what would look like a random live edge on a piece that does not currently have
stephen thomas Today, 6:04 PM

Oilstones sharpening

What do you use to shape a blade up, say if you get a flea-market chisel or plane, etc?
Do you use a grinding wheel? Or do you have to start with
stephen thomas Today, 5:55 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Ken Glass

Recent Polls

Recent Forum Posts

Recent Blog Posts