Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Yesterday, 11:20 PM

Residential fence rules
Thread Starter: Stan Calow
I am looking for what people in other jurisdictions have dealt with. I have always understood that, in my city, fences between homes were the responsibility of the homeowner who first puts it up. And the rule was "good side out" and 6" off the property line. But after a discussion with a...
Last Post By: Jim Becker Today, 11:06 AM

Seeking Recommendation on a Bench Grinder with Specific Features.
Thread Starter: Scott Memmer
Hi, Everyone. I dearly love this forum, although I have not posted in a long time. You folks are so knowledgeable and always have such great suggestions. Here is my situation. I make a small music accessory and need to build my own saw. Without going into all the details, I've been searching for...
Last Post By: Ray Selinger Yesterday, 5:12 PM

California bans gas lawn mowers and leaf blowers after 2024
Thread Starter: Bill Dufour
Saw a sign at hoe despot and looked it up. California has banned the sale of gas lawnmowers and leaf blowers after 2024. If yours is getting tired better buy a new one in a few months. I assume they will be gone from stores by Fall. It will probably take ten to twenty years until this ban goes...
Last Post By: Edward Weber Today, 4:34 PM

Harvey COMPASS RG-1/RG-2 Universal Roller Guides Question
Thread Starter: James Cheever
All - Has anyone seen or used the Harvey COMPASS RG-1/RG-2 Universal roller guides. They look solid and would be a pretty useful addition to my shop, but the price seems way too high. I'd love to hear any feedback. Thanks.
Last Post By: Lloyd McKinlay Yesterday, 9:46 PM

Grease..... and not the movie....
Thread Starter: Karl Card
I have a baldor 7.5HP BALDOR 3450RPM 213T TEFC 1PH MOTOR L3709Ton my table saw. What type of grease should I look for to put grease in the grease or zirk fitting?
Last Post By: Roger Feeley Today, 3:24 PM

Duan Packard

There is no available content written by Duan Packard

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Youthful Adventures

Saw that movie at the drive-in with my family. My dad was a desert racer in SoCal back then and he was familiar with some of the people in the movie.
Pat Germain Today, 4:46 PM

Need a New Resaw Blade

That makes sense. Thanks.

Interestingly, back in 2008 it seemed like everyone swore by Timberwolf. Seems the perceptions have changed.
Pat Germain Today, 4:42 PM

California bans gas lawn mowers and leaf blowers after 2024

There are benefits to be sure BUT at present, the technological reality we're in has a big hole in it and the proposed benefits can't actually be realized
Edward Weber Today, 4:34 PM

2 flute vs 4 flute Question

More 'memb'ring ... when I started there they were using bits for cutting drywall to clear electrical boxes. Blunt tip for a pilot, and they were grinding
Wes Grass Today, 4:26 PM

As close to a perfect fence as I’ve found so far

I was becoming more dissatisfied with the fence that came with the Sawstop and replaced it with a fence from Very Super Cool Tools. This fence is made
Cliff Polubinsky Today, 4:26 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Duan Packard

Recent Polls

Recent Forum Posts

Recent Blog Posts