Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Yesterday, 11:20 PM

Residential fence rules
Thread Starter: Stan Calow
I am looking for what people in other jurisdictions have dealt with. I have always understood that, in my city, fences between homes were the responsibility of the homeowner who first puts it up. And the rule was "good side out" and 6" off the property line. But after a discussion with a...
Last Post By: Terry Therneau Yesterday, 11:02 PM

Seeking Recommendation on a Bench Grinder with Specific Features.
Thread Starter: Scott Memmer
Hi, Everyone. I dearly love this forum, although I have not posted in a long time. You folks are so knowledgeable and always have such great suggestions. Here is my situation. I make a small music accessory and need to build my own saw. Without going into all the details, I've been searching for...
Last Post By: Ray Selinger Yesterday, 5:12 PM

Harvey COMPASS RG-1/RG-2 Universal Roller Guides Question
Thread Starter: James Cheever
All - Has anyone seen or used the Harvey COMPASS RG-1/RG-2 Universal roller guides. They look solid and would be a pretty useful addition to my shop, but the price seems way too high. I'd love to hear any feedback. Thanks.
Last Post By: Lloyd McKinlay Yesterday, 9:46 PM

Anyone with temperature controller experience?
Thread Starter: Doug Garson
I'm volunteering for a food bank and trying to set up a cold room to store produce and other perishables. The main cooling will be done by a pair of air conditioners controlled by a Coolbot which enables the air conditioners to cool the room down below the usual lower limit for air conditioners...
Last Post By: Bill Dufour Yesterday, 4:20 PM

California bans gas lawn mowers and leaf blowers after 2024
Thread Starter: Bill Dufour
Saw a sign at hoe despot and looked it up. California has banned the sale of gas lawnmowers and leaf blowers after 2024. If yours is getting tired better buy a new one in a few months. I assume they will be gone from stores by Fall. It will probably take ten to twenty years until this ban goes...
Last Post By: Ole Anderson Today, 9:41 AM

Ron Meeks

There is no available content written by Ron Meeks

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Norfab Ducting

For those of you that have made the transition to Norfab duct for their duct collection I have a question. Has anyone that had snap lock pipe retained
Rob Burch Today, 9:59 AM

PSA: I am alive for the next three years

Like the scheduled transfer idea. I just have a reminder setup on my computer calendar to do an annual transfer on a couple of accounts.
Bill Howatt Today, 9:55 AM

glass removal problem

I see you already have it done. I ran into the same a bit ago and I used a heat gun on the glass on low and it softened up the caulk enough that I could
Larry Edgerton Today, 9:54 AM

titebond clamping force for wasteblocks

I think one of the keys is that you don't require the maximum holding force for your application to work satisfactorily. Also, they say the full holding
Bill Howatt Today, 9:52 AM

Stanley No 6 Corrugated

Price drop to $80 plus shipping.

Cliff
Cliff Polubinsky Today, 9:51 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Ron Meeks

Recent Polls

Recent Forum Posts

Recent Blog Posts