Will I regret selling the Incra Super System

[David Buchhauser]

Hi Todd,
I purchased the Incra LS Standard System earlier in the year. At that time, there was about a 2 month lead time due to high demand. I was just checking the Incramental website and I see that it indicates up to 9 weeks delay for orders on the Super System. So I would imagine that you would not have too much trouble selling it at a decent price if you decide to do so. I'm not sure how much you could get for it - maybe $250 to $300 range I'm guessing. The current price is over $400 for a new one. You could build (or buy) a pretty nice fence and have money left over. It would take up less room on the table, and would most likely be easier/quicker for you to set up and use. So if you don't foresee doing anything except simple profile edging with your router table - then I would say to "go for it".
David

[Ray Newman]

In my opinion, you answered your question when you wrote: "If the only thing I ever use the router table for is to put a profile on the edge of a board, and that is very seldom"....

[Frederick Skelly]

Like you, the only thing I ever use my router table for is to put a profile on the edge of a board. (I also cut my DTs by hand.) So I have a very simple router table and a homemade fence. I've never needed more for the work I do.

So maybe try this. Take the Incra system off your router table. Pack it carefully, write the date on it and put it in your attic. Wait 6 months. If you don't miss it, either leave it packed or sell it off then.

Take care.
Fred

[David Buchhauser]

Hi Todd,
I thought about this since my original response. I agree completely with Frederick. Build the DIY router fence first and see how you like it. If you don't miss the LS system - then you might consider finding a new home for it.
David

[Joe Cowan]

You can have my Incra system when you pry it from my cold dead fingers.

[Todd Zucker]

I guess i already did the 6-month test. The assembled unit has been hanging on the wall rack for well over a year. Only time it’s moved has been to rearrange the wall rack.

Maybe I need to sell the entire setup and use the money to buy a set of hollows and rounds.

[Ted Reischl]

I have the earlier version of the SS. Mine is now about 25 years old. It is hanging on the wall above the shop door. For the most part it stays there, but I am not going to sell it because every now and then I really need it.

What I did was mount it on a sub base. I installed threaded inserts on the router table so that I can easily reinstall it when needed. I have a small shop so that thing sticking way out was an issue so that is why it hangs on the wall until really needed. I also made a simple fence that hangs on the side of the router table for "normal" use.

Would I sell it if I were you? Nope. Tools are something that wait until you need them. Sure as shooting, if you sell it in about a month or so you will wish you hadn't. It could be that right now you are not using it much, but your interests in woodworking could change over time and it would be handy to have it.

BTW, I think cutting dovetails with an Incra is a PITA. I have done it and it is a lot of fiddling around. To do dovetails I purchased a Porter Cable dovetail jig. Since virtually all drawers are made with 1/2 stock I have the jig set up to do them. It only takes a few minutes to adjust the depth of the bit in the router and away I go. Way, WAY faster than one can do them on an incra system.

[Chris Hachet]

You can have my Incra system when you pry it from my cold dead fingers.

Pretty much they way i feel about mine.

Chris

[Mike Goetzke]

I had the Super System when I had my router in the TS wing. I too had problems getting good repeatable DT's. I down sized my TS (actually tried to do without one) from a 3HP Uni with 52" fence to a smaller footprint 1950 Uni. Sold the Incra when I sold the big Uni and built a dedicated router table/cabinet with WP's top/lift/Super Fence and couldn't be happier. I also purchased a Leigh RTJ400 DT jig. I'm a hobbyist so don't make DT's all the time and found the learning curve, adjust-ability, and accuracy of this jig to be much better than the Incra and two P-C models I previously owned.

Mike

[Alan Lightstone]

I got rid of mine because it was on a table saw extension, and just took up too much space. If I had a large router table I would have kept it. Its repeatability was superb.

[Grant Wilkinson]

I use my positioner a lot. I make picture frames and note the settings each time I make a new profile. I like that I can repeat a profile months later. It allows me to use stock from a previous run with a new run.