View Profile: Mike Null - Sawmill Creek Woodworking Community

03-19-2023, 2:48 PM

Bruce Page replied to a thread Pocket knife vs TSA in Off Topic Forum

His Rusty Brick Road album is mellow and laid back. Yes, he was taken from us too soon. One day, we will beat cancer.

28 replies | 1290 view(s)

03-18-2023, 2:14 PM

Bruce Page replied to a thread Pocket knife vs TSA in Off Topic Forum

This is on my travel playlist.. https://davidmbailey.com/track/2192392/airport-song-aka-the-butt-song

28 replies | 1290 view(s)

03-16-2023, 5:20 PM

Michael J Evans replied to a thread Unifence/saw cursor accuracy and adjustment. in General Woodworking and Power Tools

Ahh gotcha. Thanks for clarifying.

10 replies | 863 view(s)

03-16-2023, 1:23 PM

Bruce Page replied to a thread Vertical Fence in CNC Machines

Very cool John. I have often wished I had made provisions for a setup like that when I built the table for my Stinger. :(

8 replies | 489 view(s)

03-15-2023, 1:08 PM

Mike Null replied to a thread A little help please in General Woodworking and Power Tools

Thank you Dave. I'll give that a try. Paul, thank you. I'm trying to avoid that but if necessary, we will add a drawer for the chessmen. But...

10 replies | 795 view(s)

03-15-2023, 11:01 AM

Mike Null started a thread A little help please in General Woodworking and Power Tools

My granddaughter is taking woodworking in her senior year of high school. Her first project was a laminated cutting board which came out...

10 replies | 795 view(s)

03-15-2023, 8:23 AM

Mike Null replied to a thread Speedy 300 air assist in Engraving Hardware and Software

Dave I'd be happy to send it to you but you need to be a contributor to send pm's. Since you have a 360 I'm sure your machine was pre-adjusted at...

6 replies | 859 view(s)

03-15-2023, 8:14 AM

Mike Null replied to a thread corel to rd-works in Laser Engraving General Topics

I know zero about RD Works but if that happened on my laser I would look at the colors I used for fill and outline. Most domestic machines require...

5 replies | 526 view(s)

03-14-2023, 6:20 PM

Mike Null replied to a thread Looking for JobControl 6 for Trotec Speedy 100 8003 in Engraving Hardware and Software

I would try newer version of Job Control. I'd be surprised if you found a version that old as there wouldn't be much need to keep it. The latest...

2 replies | 250 view(s)

03-13-2023, 11:13 PM

Michael J Evans replied to a thread contact cement flammability? in General Woodworking and Power Tools

Good to know. Thanks Andrew

13 replies | 900 view(s)

03-13-2023, 1:44 PM

Bruce Page replied to a thread Where do post go to die? in Forum Tech Support

Bruce, there were no posts removed from that thread. We do not remove posts (ever) unless they violate the TOS.

4 replies | 750 view(s)

03-13-2023, 10:33 AM

Michael J Evans replied to a thread contact cement flammability? in General Woodworking and Power Tools

Hi John Here in the PNW it hasn't been real warm. Maybe usually 40s-60s this time year.

13 replies | 900 view(s)

03-13-2023, 2:40 AM

Michael J Evans replied to a thread contact cement flammability? in General Woodworking and Power Tools

Dave / Larry Thanks. How long would you leave the door open for ventilation? Like just whole applying, 3-4 hrs afterwards,etc?

13 replies | 900 view(s)

03-13-2023, 12:18 AM

Michael J Evans started a thread contact cement flammability? in General Woodworking and Power Tools

Hello Getting ready to put some laminate on MDF for a router table top build. Decided to read the contact cement can and at the very top in bold...

13 replies | 900 view(s)

03-13-2023, 12:10 AM

Michael J Evans replied to a thread Unifence/saw cursor accuracy and adjustment. in General Woodworking and Power Tools

Bill Great idea. I just have no idea how I'd accurately clamp anything in that tiny space. Likely I'll just have to do lots of trial and error to...

10 replies | 863 view(s)

03-13-2023, 12:08 AM

Michael J Evans replied to a thread Unifence/saw cursor accuracy and adjustment. in General Woodworking and Power Tools

Hi Ron I think your right. Just get it very close then bump fence from there. Only thing is I think I'd rather have the cursor cut a little fat then...

10 replies | 863 view(s)

03-12-2023, 7:57 PM

Michael J Evans started a thread Unifence/saw cursor accuracy and adjustment. in General Woodworking and Power Tools

Hi All I'm gearing up for a project and haven't touched my tools in a long while. Long of the short I decided to check blade/miter/fence...

10 replies | 863 view(s)

03-12-2023, 2:33 PM

Bruce Page replied to a thread Who to contact for contributions / problem question? in Forum Tech Support

Richard, the “Contact Us” at the bottom of every page would be a more direct route. I will also bring your post up in the Moderators forum.

5 replies | 564 view(s)

03-11-2023, 10:20 AM

Steve Schlumpf replied to a thread Finishing Ebony in Turner's Forum

Very little experience with Ebony but seem to remember that it is an oily wood and, as such, will need to be cleaned with acetone or lacquer thinner...

5 replies | 727 view(s)

03-11-2023, 9:25 AM

Keith Outten replied to a thread Bandsaw instead of tablesaw? in General Woodworking and Power Tools

I have not used my table saw but three times in the last couple of years. Since I got my FB 610 it is my go to machine for most jobs. I can rip cut...

24 replies | 1631 view(s)

Mike Null
Moderator

Mini Statistics

More 16 Friends

Jarami Reid

Andy Hoyt

Keith Winter

Josh Stephens

Albert Aguilar

Amie McGee

Join Groups 1 Groups

Trotec Laser Engravers Users Group

Join Groups 0 Permission Groups

Recent Visitors

2 Visitor Messages

Basic Information

About Mike Null

Signature

Contact

Statistics

Total Posts

Visitor Messages

General Information

16 Friends

Albert Aguilar

Amie McGee

Andy Hoyt

Bruce Page

Chris Padilla

Clem Harriss

Dylan ritterbeck

Edward Henry

Eric Burke

Jarami Reid

Mike Null Moderator

Mini Statistics

More 16 Friends

Join Groups 1 Groups

Join Groups 0 Permission Groups

Recent Visitors

2 Visitor Messages

Basic Information

About Mike Null

Signature

Contact

Statistics

Total Posts

Visitor Messages

General Information

16 Friends

Mike Null
Moderator