Search:

Tag: turning

Search: Search took 0.00 seconds.

  1. Finishing Bowl Bottoms

    Started by Steven Park, 01-30-2018 1:45 PM
    2 Pages
    1 2
    • Replies: 22
    • Views: 1,675
    Last Post: 02-08-2018 3:15 PM
    by Peter Blair  Go to last post
  2. Craftsman monotube lathe tuneup help needed

    Started by Jay Pugsley, 12-30-2015 7:44 AM
    lathe, lathe repair, turning
    • Replies: 6
    • Views: 2,148
    Last Post: 01-02-2016 10:10 AM
    by david privett  Go to last post
  3. Wood lamp type of finish to use?

    Started by Kasey Miller, 08-24-2015 8:17 AM
    • Replies: 0
    • Views: 690
    Last Post: 08-24-2015 8:17 AM
    by Kasey Miller  Go to last post
  4. Whats the best lathe for...

    Started by Kyle Atkinson, 08-18-2015 8:37 PM
    help!!!!lol, turning
    • Replies: 11
    • Views: 2,523
    Last Post: 08-19-2015 10:02 AM
    by Dennis Ford  Go to last post
  5. Red Mallee Burl

    Started by Rick Edwardson, 05-27-2015 4:35 PM
    • Replies: 3
    • Views: 1,348
    Last Post: 05-27-2015 8:09 PM
    by david privett  Go to last post
  6. Lathe repair

    Started by Clay McElwee, 01-28-2015 10:54 AM
    • Replies: 9
    • Views: 3,097
    Last Post: 02-15-2015 6:05 PM
    by Russell Neyman  Go to last post
  7. Turning Green Wood

    Started by Dan DeBruler, 08-06-2014 7:05 AM
    green, pear, turning, wet
    • Replies: 10
    • Views: 2,703
    Last Post: 08-08-2014 11:22 AM
    by Reed Gray  Go to last post
  8. Shop Built Bowl Lathe

    Started by Michael Poorman, 11-11-2013 1:50 PM
    2 Pages
    1 2
    • Replies: 25
    • Views: 4,905
    Last Post: 11-22-2013 7:14 PM
    by Ron Page  Go to last post
  9. Bowl gouge size

    Started by Victor Robinson, 01-17-2013 9:18 PM
    2 Pages
    1 2
    gouges, lathe, turning
    • Replies: 24
    • Views: 6,516
    Last Post: 01-19-2013 12:36 PM
    by Reed Gray  Go to last post
  10. Parting Multiples From Spindle Problem

    Started by Chris Harvan, 09-09-2012 8:49 AM
    parting, turning
    • Replies: 10
    • Views: 1,582
    Last Post: 09-09-2012 8:54 PM
    by Chris Harvan  Go to last post
  11. Blood wood cane.

    Started by John Gregory, 05-07-2012 10:38 AM
    • Replies: 10
    • Views: 2,428
    Last Post: 05-09-2012 4:57 PM
    by Mike Null  Go to last post
  12. Segmented Bowl

    Started by Lee Alkureishi, 03-04-2012 9:01 PM
    • Replies: 11
    • Views: 2,676
    Last Post: 03-06-2012 11:11 AM
    by Bill Wyko  Go to last post
    • Replies: 11
    • Views: 2,226
    Last Post: 01-13-2012 2:55 PM
    by Thomas Heck  Go to last post
  13. General International 25-300 vs. Jet 1220VS

    Started by Ron Kahn, 05-01-2011 7:07 AM
    advice, general international, jet, lathes, turning
    • Replies: 6
    • Views: 2,797
    Last Post: 05-08-2011 3:13 PM
    by Ron Kahn  Go to last post
    • Replies: 11
    • Views: 1,913
    Last Post: 03-30-2011 9:59 PM
    by Lori Kleinberg  Go to last post
  14. Finally turned some pendants

    Started by John McCaskill, 12-16-2010 2:38 PM
    • Replies: 5
    • Views: 2,089
    Last Post: 12-16-2010 11:06 PM
    by Bernie Weishapl  Go to last post
  15. Turning Some Bottle Stoppers

    Started by Trevor Walsh, 10-02-2010 6:25 PM
    • Replies: 6
    • Views: 2,654
    Last Post: 10-02-2010 8:26 PM
    by Mark Hubl  Go to last post
  16. Good deal on a Lathe & stuff, possible gloat

    Started by Lori Kleinberg, 02-10-2010 4:17 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 4,570
    Last Post: 02-11-2010 11:00 AM
    by Lori Kleinberg  Go to last post
  17. New Member Here

    Started by Chris Brittain, 01-12-2010 11:33 PM
    lumber, sawmill, turning, wood
    • Replies: 13
    • Views: 3,990
    Last Post: 01-14-2010 8:44 AM
    by Chris Brittain  Go to last post
Results 1 to 19 of 20