In the laser engraving forum a thread with Dropbox in the title , when I try to open that thread I get a virus warning pop up and it will not let me open that thread. Is there a problem?Threat.jpg
In the laser engraving forum a thread with Dropbox in the title , when I try to open that thread I get a virus warning pop up and it will not let me open that thread. Is there a problem?Threat.jpg
Last edited by Bert Kemp; 09-11-2020 at 10:23 AM.
If the Help and advice you received here was of any VALUE to you PLEASE! Become a Contributor
Rabbit RL_XX_6040-60 watt Laser engraving/cutting machine Oh wait its a 3D Printer my bad LOL
Lasercut 5.3
CorelDraw X5
10" Miter Saw with slide
10" Table Saw
8" bench mount 5 speed Drill Press
Dremel, 3x21 Belt Sander
Looks like your anti-virus software is working. I would accept that it has identified a threat and go somewhere else. If you don't trust your AV software it isn't doing you any good. Switch to one you trust. You could also email or IM the forum and get input from their admins to confirm that your AV software is wrong if that is what you suspect.
"A hen is only an egg's way of making another egg".
– Samuel Butler
Bert, I can't find the link you mentioned possibly it was removed.
I think this is the thread:
https://sawmillcreek.org/showthread....on-*-cdr-files
I moved the thread to the moderator forum. I get an alert just trying to open the thread.
Lee Schierer
USNA '71
Go Navy!
My advice, comments and suggestions are free, but it costs money to run the site. If you found something of value here please give a little something back by becoming a contributor! Please Contribute
Dropbox hanging on *.cdr files
Right I cant open the thread
Started by Chuck Phillips, 09-09-2020 11:59 AM
If the Help and advice you received here was of any VALUE to you PLEASE! Become a Contributor
Rabbit RL_XX_6040-60 watt Laser engraving/cutting machine Oh wait its a 3D Printer my bad LOL
Lasercut 5.3
CorelDraw X5
10" Miter Saw with slide
10" Table Saw
8" bench mount 5 speed Drill Press
Dremel, 3x21 Belt Sander
This thread is still there and I still can't open the thread. Is this thread dangerous it says it has some virus.
If the Help and advice you received here was of any VALUE to you PLEASE! Become a Contributor
Rabbit RL_XX_6040-60 watt Laser engraving/cutting machine Oh wait its a 3D Printer my bad LOL
Lasercut 5.3
CorelDraw X5
10" Miter Saw with slide
10" Table Saw
8" bench mount 5 speed Drill Press
Dremel, 3x21 Belt Sander
so what are you saying I should run out and spend 800$ on a mac to open one thread?
If the Help and advice you received here was of any VALUE to you PLEASE! Become a Contributor
Rabbit RL_XX_6040-60 watt Laser engraving/cutting machine Oh wait its a 3D Printer my bad LOL
Lasercut 5.3
CorelDraw X5
10" Miter Saw with slide
10" Table Saw
8" bench mount 5 speed Drill Press
Dremel, 3x21 Belt Sander
Save your money Bert. I opened it on two PC’s and didn’t have any warnings. I’m not sure what’s going on.
Trust me I wouldn't waste a dime on anything apple. But I would like to figure out why I get the virus threat
If the Help and advice you received here was of any VALUE to you PLEASE! Become a Contributor
Rabbit RL_XX_6040-60 watt Laser engraving/cutting machine Oh wait its a 3D Printer my bad LOL
Lasercut 5.3
CorelDraw X5
10" Miter Saw with slide
10" Table Saw
8" bench mount 5 speed Drill Press
Dremel, 3x21 Belt Sander