I posted this exact same question the other day piggybacking on someone else's thread, following keenly
I posted this exact same question the other day piggybacking on someone else's thread, following keenly
Gary, I'm looking for something just like this to work with an automated process. Do you happen to remember where to connect into the board?
Thanks!
Universal 60w VLS6.60 w/ rotary
RayFine 30w MOPA
Corel X8, Photoshop
Fab shop with South Bend Heavy 10, Bridgeport 9x42, 185a welder and a multitude of supporting tools/equipment
I forget if you can change the duration of the 5v output. If so, there are some simple 5v beepers out there that take next to nothing for current that you could likely wire up directly.
Else, you can also look up "flip-flop" relays or circuits. A pulse will turn the relay on, a second pulse will turn it off. You can hook up a strobe, light, whatever to the relay. Then you can either have a pushbutton to flip it back off or configure another pulse from the program when you start the next job.
Regardless, Arduino will totally work (heck, they're overkill for this as they are really quite capable), but there are also some inexpensive, almost turn key options out there that will work.
Licensed Professional Engineer,
Unlicensed Semi Professional Tinkerer
I have a $25 Casio watch with a 'stepped' one-button countdown timer, works in 1, 3, 5, 10, 20 and 30 minute increments, if I want 1 minute, press once, 5 minutes press 3 times, etc. I have one repeat job that takes 5:54 to run- before I change the part out I press 3 times, change, load, start--- when the timer goes off, by the time I get to the machine it's usually just getting done
Speaking of timers, I have a couple of these small digital timers I got at the dollar store, you can set them to the second, and they retain the setting until you specifically reset it.
timer.jpg
Not perfect solutions but they help!
========================================
ELEVEN - rotary cutter tool machines
FOUR - CO2 lasers
THREE- make that FOUR now - fiber lasers
ONE - vinyl cutter
CASmate, Corel, Gravostyle
Thanks Gary! Did you end up with the Arduino stuff or some other solution?
Universal 60w VLS6.60 w/ rotary
RayFine 30w MOPA
Corel X8, Photoshop
Fab shop with South Bend Heavy 10, Bridgeport 9x42, 185a welder and a multitude of supporting tools/equipment
Business opportunity! Make up something that works and I'll buy one for a Dolla! or maybe I'd go Two dolla!
Woodworking, Old Tools and Shooting
Ray Fine RF-1390 Laser Ray Fine 20watt Fiber Laser
SFX 50 Watt Fiber Laser
PM2000, Delta BS, Delta sander, Powermatic 50 jointer,
Powermatic 100-12 planer, Rockwell 15-126 radial drill press
Rockwell 46-450 lathe, and 2 Walker Turner RA1100 radial saws
Jet JWS18, bandsaw Carbide Create CNC, RIA 22TCM 1911s and others
I ended up having an Arduino solution made for me. I didn't know anything about Arduino at the time and didn't want to learn another programming language so I found someone with the expertise and experience to do it for me. He designed a board, wrote the code and ended up with a really nice product. Unfortunately I got too busy to install it and get it working so it is actually sitting in my home office somewhere among the rest of the Arduino stuff I started on after that. The person is a member here, Doug Griffith, and maybe he could help you to modify what he has done already to meet your needs. I can search for the parts I have at home but it may take me a while as I'm in the middle of finishing a 1,900 sq ft basement and my Arduino stuff is boxed up *somewhere*... If you want to message Doug his post to me is earlier on this thread, and maybe he can help.
Thanks Gary for the reply.
Universal 60w VLS6.60 w/ rotary
RayFine 30w MOPA
Corel X8, Photoshop
Fab shop with South Bend Heavy 10, Bridgeport 9x42, 185a welder and a multitude of supporting tools/equipment