I directed mine into a stud cavity with a 6" at the bottom. No collection at the saw port, it just spits into the stud cavity using an old rubber 90 from my dad's old Dewalt RAS..
I directed mine into a stud cavity with a 6" at the bottom. No collection at the saw port, it just spits into the stud cavity using an old rubber 90 from my dad's old Dewalt RAS..
NOW you tell me...
Thanks. I also have many long term "temporary" setups...
John, my apologies for the delay but here it is. The one big draw back is that the saw cannot be rolled fully left and right but the offending bits of the shroud could be hinged or even made removeable if needed. I am using a CV1800 to power the hood through a single 6" duct and it collects nearly everything. I put it on a sliding base as the fences each side are fixed and if I use a sub fence on the saw I can wind it in or out to line up the fences. All dust goes in the bottom and drawn out the top so it needs a good dust extractor to make this hood work. The curved plenum is made from 3mm MDF, I made a rough form, wet the MDF and clamped it to the form for a few days to dry. The bottom inlet must be sized to at least match the area of a 6" duct. Any questions or if I can be of further help please ask.
Sliding Base.JPG
Glide Saw Installed.jpg
Blast Gate Installed in Top Plenum.JPG
Air Entry at Bottom of Hood.JPG
IMG_1580.JPG
IMG_1581.JPG
Last edited by Chris Parks; 12-14-2018 at 10:04 PM.
Chris
Everything I like is either illegal, immoral or fattening
Continuing due to post limitations.
IMG_1595 Plenum Shown.jpg
IMG_1598.jpg
Top View.jpg
Last edited by Chris Parks; 12-14-2018 at 10:05 PM.
Chris
Everything I like is either illegal, immoral or fattening
I don't have a miter saw and wasn't going to reply to this thread but thought I'd go ahead and show the set-up my radial arm saw since it is a somewhat similar concept.
I installed a rather basic collector with a 4" port at the bottom connected to a Grizzly 2hp dust collector. Prior to this, my wall and floor was covered with sawdust after any use and after the modification I only have minimal sawdust, primarily in front of the fence. I would think that anything 4" or up would have a good chance of giving good performance (depending on the design), though anything below might be questionable.
I've attached a few pictures to show the set-up. Please excuse the blade that is on the saw and it is pretty rough. I occasionally work with reclaimed wood and prior to stacking & storage I will remove unusable and nail-filled sections, so use an old blade to save wear and prevent damage to my better blades.
RAS DC 1.jpgRAS DC 2.jpgRAS DC 3.jpg
Chris, thanks for posting all the pics and explanation. I really like your design and will now plan on going that route. I especially like that even though the collection area is at the bottom and the DC duct is at the top the saw is still very close to the wall (the reason I bought the Bosch).
The idea of having some forward/aft movement to accommodate a sacrificial fence is also very good. I always use 1/2" MDF for such fences. So instead of using a knob and threaded rod I would use a couple of 1/4" pins on that forward cross piece and have 2 holes (1 set on each side) drilled 1/2" apart on the base. That would make my changeover faster and my big hands wouldn't have to fumble around with a knob under the slider since you really have to adjust it at 0 degrees.
My one question would be about your factory dust chute. I see that you have the original 90 degree rubber fitting on yours. If you are cutting a 45 or greater miter to the right does some sawdust escape from that fitting being so close to the left front of the shroud?
It doesn't seem to cause any problems but I will remove it and see what happens. I did have it hooked up to the plenum of a previous hood with a small hose but the whole hood was a hopeless case converted from when I had a different saw. I move the sliding base with a cordless drill on the nut, it was very handy doing the initial fence set up to get it spot on. My bench fences are sitting on pins so I can lift them off and use the benches as needed.
Last edited by Chris Parks; 12-15-2018 at 7:51 PM.
Chris
Everything I like is either illegal, immoral or fattening
Thanks Chris. Staring at the pictures again I realize now that you don't have to have the saw at zero to adjust for your sacrificial fences. You just have to adjust them to be even with the extra cabinet fences on the left and right side.
And I like your side bracket to hold the clamp. Makes access to it easy but keeps it out of the way when not used.
I'm not familiar with the electrical system in Australia but it appears you may have changed the plug on the saw. That was one of the first things I did on mine. Power tools like this that draw a lot of current have heavier gauge wire making the cord heavy to the point where the factory straight in plug won't stay in the outlet very well. I think it's somewhat of a safety hazard and could lower the performance of the tool due to a poor connection. This is now the third tool I have with a heavy cord that I've changed the plug over to a 90 degree one.
John, the electrical plug is standard in Oz, we use 240V single phase for all single phase and 415V for all three phase. if you want the original picture files PM me your email address and I will send them to you.
Chris
Everything I like is either illegal, immoral or fattening
Just an observation: While trimming out my son's house with painted MDF, it became apparent that 4" or 6" stock sawed while laying flat spewed dust all over, while if cut standing vertically, dust almost shot exclusively into the dust collection chute. Also (not a surprise) cutting wood vs MDF, dust tended to be directed to the chute in a much more controlled manner.
NOW you tell me...
I just plumbed the whole shops this summer. Went with the Dust Deputy XL since DC has a 6" port. I did a 6" to the cabinet behind my miter saw (also to TS and Jointer). I can hold my hand up to the opening and feel the air flowing in.
If over thinking was an Olympic event, I'd win Gold every time!