Results 1 to 5 of 5

Thread: How To Make Windows

  1. #1

    How To Make Windows

    Hello All,

    I just found your great resource foroum a few months ago,
    this a terrific place to learn and share, that's for sure.

    I am looking to build some single pane windows for the exterior of a 100 year old General Store that is our shop, and Pottery studio.

    I am not having much luck with search engines, searching for "How To Make Windows" comes up with tons of Microsoft info, but no real "how to's" for construction with wood.

    Same thing when looking for books - tons of stuff on window dressing, but little on building?

    Does anyone have a good source suggestion?

    Thanks in advance,
    Bob

  2. #2
    Hi Bob,
    I need to make a bunch of windows myself. I ordered this set and sometime in the near future i will embark on giving this a try. I am a total beginner but have looked and found very little about buiding windows.
    http://www.woodcraft.com/family.aspx?FamilyID=8285

    there are better prices than woodcraft. keep in mind i havent built any yet, but the process looks pretty straight forward. hope this helps some.

  3. #3
    Hi Bob,

    I had to do the same thing this summer for my old building. Wood Magazine has an article on how to do it with bit sets like the CMT sash set.

    http://www.woodmagazine.com/wood/sto...ml&catref=wd21

    Have fun.

  4. #4

    Making Window a Sash

    Folks
    Made 10 windows for a Maple Syrup evaporation building this past fall.
    All are single sash not double sash - hence easier.
    Some are fixed and some tilt inward.
    Sizes are: 9 of them about 30 x 48 with 9 lights;
    and one of them is 24 x 72 with 16 lights

    Lets see: equipment used
    Number one and most important - get a "sled" for the clamping and set up of the rail end cut. Buy the steel sled from Delta or one of the aftermarket sleds . The rail "end grain" cut is the important dimension in order to have the horizontal muntins fit the one piece vertical muntins.

    bench top mortiser
    band saw
    table saw
    cross cut miter saw
    router table
    router bits = Freud 99-050 and 99-051
    The instructions have a couple of incorrect dimensions. But will keep you on the straight and narrow.
    Because they can also be spaced out to 1-1/2 inches, by experimentation.
    I stuck with 1-3/8 inches thick

    Made the windows 1-3/8 inch thick; rails and stiles
    Top rails = 2-1/4
    Bottom rail = 3-1/4
    Stiles = 2-1/4
    Made the muntins 1 inch wide but should have made them wider - maybe 1-1/4 inch wide - Why?
    Because it would have given the glazer more of a rabbet to set the glass.

    There are allot of little sub sequences that have to be done to make things fit correctly. Mainly: get two routers and two plates for your router table. Set up the routers for the proper height and switch between. It gets ugly at times switching back and forth.

    Well that touches on the process except to say - get the processes straight in your head and stick by them. I have the time to do one process a day (retired) and that's how I got through it successfully.
    I do have some photos on another website, but you've seen windows.
    Daniel
    "Howdy" from Southwestern PA

  5. #5
    Join Date
    Feb 2005
    Location
    Sterling CT
    Posts
    2,457
    the latest issue of FWW has an article all about it.

    lou

Similar Threads

  1. Tips and ideas for lasers
    By Rodne Gold in forum Laser Engraving General Topics
    Replies: 23
    Last Post: 03-18-2009, 1:45 AM
  2. Replacing Windows part II: Andersen vs Andersen
    By Dan Mages in forum Off Topic Forum
    Replies: 22
    Last Post: 10-03-2005, 8:07 PM
  3. Replacing old windows
    By Dan Mages in forum Off Topic Forum
    Replies: 12
    Last Post: 09-22-2005, 9:28 AM
  4. best sprayable finish for windows?
    By Tim Brewers in forum Project Finishing
    Replies: 4
    Last Post: 06-14-2005, 11:22 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •