Has anyone replaced them?
Has anyone replaced them?
We have a Hunter in the highest part of the cathedral ceiling on a 6' down rod. It's been running continuously for over 10 years. I'm not sure they have bearings, or bushings in them, but it started making some noise over a year ago. I bought another fan, but while I was waiting for that one to come, I put some 3-n-1 oil on top where the downrod screws into it for it to run down into whatever was below. It hasn't made any noise again since. It's been running continuously since then, and the new one is still in the box.
Thanks Tom, This fan is at least 30 years old. I wanted to oil it- wasn't sure where to put the oil w/o taking the fan down.
I've got a Casablanca fan that's been running 24/7 since 1992, except for two days last fall when I repainted the ceiling in that room. Still as quiet as the day I installed it.
At this point I suspect it will outlive me.
Yoga class makes me feel like a total stud, mostly because I'm about as flexible as a 2x4.
"Design"? Possibly. "Intelligent"? Sure doesn't look like it from this angle.
We used to be hunter gatherers. Now we're shopper borrowers.
The three most important words in the English language: "Front Towards Enemy".
The world makes a lot more sense when you remember that Butthead was the smart one.
You can never be too rich, too thin, or have too much ammo.
Yeah, ours has been running for a lot longer than 10 years. I remember putting it up right before I left to take our Son to his first Boy Scout Summer Camp. He's 40 now.
Different fixes for different fans.
Hunter used to advertise that competitors used dishwasher motors.
Also remember do not over oil. You don't want oil to get into the motor windings.
I haven't priced a ceiling fan in years. The used to be priced in a range low enough to make replacement a sensible choice.
jtk
"A pessimist sees the difficulty in every opportunity; an optimist sees the opportunity in every difficulty."
- Sir Winston Churchill (1874-1965)
I have to set scaffolding up to replace that one, and just have a lot of other stuff on the to-do list, so it gets put off until absolutely necessary.
I just put up two Honeywell's last week on an outside porch, after a recommendation by BIL. They work fine, and weren't too hard to get in perfect balance with the plastic blades. BIL has some working for years on an outside porch in salt air.
I had to take apart 3 outside fans not for bearing but to remove mud dauber nests.
Steve Jenkins, McKinney, TX. 469 742-9694
Always use the word "impossible" with extreme caution
If/when it gets noisy again, or before you grab 3-in-one, or WD40, or any other light lube for a hinge or whatever-
Go to Lowes and buy a can of "Super Slick Slick Stuff"--
supslk.jpg
Don't know what's in it, but it puts WD40 and Walmart's 'spray lubricant' to absolute shame. Not sure how it compares to Liquid Wrench, not sure it'll loosen bolts, but wouldn't surprise me
My main source of evidence; our main bathroom door would need a shot of lube about every 3 months, just to keep the hinges from squeaking. I sprayed the hinges with this stuff over a year ago and not only do the hinges not squeak, the door still glides closed till it hits the strike plate with just a gentle push. Smells good too
========================================
ELEVEN - rotary cutter tool machines
FOUR - CO2 lasers
THREE- make that FOUR now - fiber lasers
ONE - vinyl cutter
CASmate, Corel, Gravostyle
Thanks. Will be adding it to my lube cabinet.
I would be surprised if the bearings are not held in by a spot welded cup or clip. Meaning you may have to drill out some welds and then use screws to reinstall. Or maybe just epoxied together like a washing machine motor end bell has been done for decades.
BilL D
Just a reminder: Traditional WD40 is not a lubricant it is largely a solvent. Same with Liquid Wrench. WD40 does make a lot of different spray products however including WD40 Specialist White Lithium Grease which is good stuff. The can looks much like traditional WD40.
Last edited by Ole Anderson; 09-09-2022 at 9:44 AM.
NOW you tell me...
While WD40 IS largely a solvent, according to it's MSDS it's first listed use is "lubricant"--
WDmsds.jpg
========================================
ELEVEN - rotary cutter tool machines
FOUR - CO2 lasers
THREE- make that FOUR now - fiber lasers
ONE - vinyl cutter
CASmate, Corel, Gravostyle
I just used 3-N-1 oil because it was what we had in the house, and I was only wanting a few days anyway, but it has lasted well over a year. Now I'm just leaving it both to put off having to stop doing other things and set scaffolding up in the house, but also just to see how long it lasts out of curiosity.
Yoga class makes me feel like a total stud, mostly because I'm about as flexible as a 2x4.
"Design"? Possibly. "Intelligent"? Sure doesn't look like it from this angle.
We used to be hunter gatherers. Now we're shopper borrowers.
The three most important words in the English language: "Front Towards Enemy".
The world makes a lot more sense when you remember that Butthead was the smart one.
You can never be too rich, too thin, or have too much ammo.