Results 1 to 11 of 11

Thread: Irresistible marking tools

  1. #1
    Join Date
    Feb 2004
    Location
    Perth, Australia
    Posts
    9,467

    Irresistible marking tools

    I admit it. I am a sucker for marking tools. I have a couple of Chris Vesper sliding bevels and squares that make me smile ever occasion I use them.








    I have bronze Tite-Mark and stainless steel Veritas wheel gauges, both works of art, and even made one of my own ...





    A mortice gauge I built (it uses sized cutters) ...





    It was inspired by the Kinshiro cutting gauge (on the right), a gift from Wiley. Very precious ...





    There are many more. This post is not about them, but a fore taste of the tool I have just purchased. It is on its way, so I cannot tell you what it is like to use. It is on a Black Friday special at present, so if there are any like-minded fools here, this is a heads up.


    I was watching this video by Adam Savage ...


    https://www.youtube.com/watch?v=PVQF...2%80%99sTested


    The question is who needs a fancy compass? Well, I will certainly use it.


    But I could just sit an look at it - some tools are art, and one really should appreciate the effort that went into both design and build ...


    The Iris drawing compass (by Makers Cabinet) ...





    https://www.makerscabinet.com/


    Regards from Perth


    Derek

  2. #2
    Join Date
    Mar 2006
    Location
    SoCal
    Posts
    22,492
    Blog Entries
    1
    Silence foul temptress!!!
    - Sir Launcelot
    "A hen is only an egg's way of making another egg".


    – Samuel Butler

  3. #3
    Join Date
    Mar 2003
    Location
    SF Bay Area
    Posts
    330
    They are all beautiful. The Drawing Compass is stunning. -Howard

  4. #4
    Join Date
    Oct 2004
    Location
    SoCal
    Posts
    866
    I met Chris in 2012 and bought a Black Red Gum cutting gauge from home. It is one of my most treasured tools. Chris makes some remarkable tools. That circular compass looks to be a jewel - but how does one center it on a point?

  5. #5
    Join Date
    Feb 2004
    Location
    Perth, Australia
    Posts
    9,467
    Good point Curt! I found this ...

    The "stand" of the IRIS also acts as a center-finding tool. You put the stand inside the fully-opened IRIS and the stand's tip is right at the circle's center. Mark your dot, remove the stand, then adjust the iris to the desired size without moving the IRIS and the dot will be in the exact center of any circle you make. There are also measurements along the outside diameter or the IRIS that let you make the exact size circle you want, or measure the size of existing circles or cylinders.





    Regards from Perth

    Derek

  6. #6
    Join Date
    Apr 2007
    Location
    Columbus, Ohio, USA
    Posts
    3,441
    I wanted the Lee Valley pencil sharpener, but missed out on that. I have the Maker's Cabinet Pencil Sharpener (hand plane pencil sharpener), it arrived and I have not had time to unpack it yet. Lots of things showed up at the same time, like my new Washita stone, and I am trying to finish my toothpick boxes. So much to do, so little time.

    Looking forward to how you like the iris.

    I expect that the center finding portion is likely to be used to make sure that you circle that you draw goes around the center as opposed to simply marking the center.

  7. #7
    Join Date
    Jan 2016
    Location
    Port au Port, NL, Canada
    Posts
    72
    I agree Derek, quality made tools are hard for me to pass over too. I'd like a set of squares from Chris Vesper but with Cherry infills, I'm waiting on my request.

  8. #8
    I appreciate looking at those expensive tools but I wouldn't buy one. I have a number of compasses that I purchased used on eBay for a few dollars each that do a fine job of drawing circles. That Iris is $123 plus shipping.

    Mike
    Go into the world and do well. But more importantly, go into the world and do good.

  9. #9
    Join Date
    Oct 2004
    Location
    SoCal
    Posts
    866
    Thanks Derek! That is a reasonably clever solution for the Iris.

    We all have to decide where our disposable income goes. For some, the concept of "disposable" is a pipe dream, others simply have a tight wallet, yet others spend and should not. Good tools often suffer from the "sour grapes" viewpoint. I may not be able to afford some tools or even wish to afford some but that does not mean I get to diss them. Superb quality is its own reason for existence in the same sense that beautiful art is.

    I could never afford a Holtey plane but I can appreciate, even from mere pictures, for the quality it represents. We really need a Tool Porn thread.

  10. #10
    Join Date
    Sep 2007
    Location
    Longview WA
    Posts
    27,347
    Blog Entries
    1
    It is a very clever tool. The way it can be centered and then the size changed without moving is a great feature. It is reminiscent of drop center compass. Though one of those usually doesn't reach enough to draw a seven centimeter circle.

    jtk
    Last edited by Jim Koepke; 12-01-2020 at 12:47 AM. Reason: corrected four to seven cm
    "A pessimist sees the difficulty in every opportunity; an optimist sees the opportunity in every difficulty."
    - Sir Winston Churchill (1874-1965)

  11. #11
    Join Date
    Apr 2013
    Location
    Issaquah, Washington
    Posts
    1,320
    Stop it Derek, you are killing my retirement budget!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •