Results 1 to 15 of 15

Thread: Lubricant for wood vice

  1. #1
    Join Date
    Jul 2006
    Location
    Central, PA
    Posts
    416

    Lubricant for wood vice

    What is the best lubricant for my vice? Obviously I don’t want the substance to become gummy and a source for sawdust to stick to.

    Thanks.

  2. #2
    Join Date
    Apr 2013
    Location
    Okotoks AB
    Posts
    3,495
    Blog Entries
    1
    I'd say wax, maybe paraffin. Bee's wax can be a little gummy.

  3. #3
    Join Date
    Aug 2017
    Location
    Arlington, TX
    Posts
    452
    I've always used a light coating of heavy oil (STP Oil Treatment is thick and has good adhesion to metal surfaces) or grease, and lived with the sawdust sticking to it. It has never bothered me.

    There are also dry lubes with Teflon, etc. that might work (I'd have to clean my vise to try them out).

    -- Andy - Arlington TX

  4. #4
    paraffin (canning wax)

  5. #5
    Join Date
    Nov 2003
    Location
    Central North Carolina
    Posts
    1,830
    I use Johnson's Paste Wax. It develops a dry crust that does not allow sawdust to stick. It stays in place and lubricates very well. I apply it with an old tooth brush to the inner workings gears, slides, and trunnions of my table saw and other woodworking shop tools, as well as to my vice. For rust prevention and to make the work slide more easily on my saw and tool surfaces I also cover them with the same wax, but apply it thin with a rag, and then go back with a clean rag after it dries, and buff off the excess. A can of it lasts me about 5 years.

    Charley

  6. #6
    Join Date
    Dec 2010
    Location
    South Coastal Massachusetts
    Posts
    6,824
    I prefer "Slipit" for wood on wood moving parts.

    No discernible residue, doesn't attract sawdust.
    Apply with a small toothbrush - a little goes a long way.

    https://www.amazon.com/Grizzly-G5562.../dp/B0000E6TJ8

  7. #7
    Lee Valley suggests 'grease' on the sides & root of the vise screw (remove it from the thread crown) in their twin screw vise instructions.
    Just a Duffer

  8. #8
    Spray graphite or teflon works very well for me.

  9. #9
    Join Date
    Nov 2009
    Location
    Peoria, IL
    Posts
    4,443
    Wait, what? "best lubricant for my vice" KY jelly I guess, but should this be posted? For my woodworking vises, I've used nothing for 40 years. None of them are worn out yet!
    Last edited by Richard Coers; 11-01-2020 at 11:28 AM.

  10. #10
    Join Date
    Feb 2008
    Location
    E TN, near Knoxville
    Posts
    12,298
    I use powdered graphite purchased from a player piano rebuilder's supplier, dabbed on with a felt applicator that came with the graphite. IMO, graphite is the best lube for wood-on-wood and not bad for wood on metal.

  11. #11
    I like bees wax, and I'm sure that was the norm. I mean ...what else did they have? Even though the stuff seems gummy
    and sticky it is great and will not need reapplication for a long time. And it's the best for metal "wood screws".

  12. #12
    Join Date
    Sep 2016
    Location
    Modesto, CA, USA
    Posts
    9,876
    When I bought another machinists vise I noticed many of them have a design problem. The cheap ones have the screw exposed above the guide bar. A much better design has the screw is below and inside the guide bar so no junk falls onto it. Of course this hides the screw and means it has to be unscrewed all the way to inspect,clean and lube it.
    Bil lD

  13. #13
    I like "Specialist Dirt & Dust Resistant Dry Lube PTFE Spray" by WD-40

  14. #14
    Join Date
    Feb 2003
    Location
    Bellingham, WA
    Posts
    1,933
    Hey, this is a family forum! Maybe we shouldn't be sharing lube advice for our wood vices.

    Or are we talking vises? That's a whole different thing, lol!

    Sorry, as a dad, I can't resist a pun invitation like that...
    JR

  15. #15
    Join Date
    Apr 2005
    Location
    Central MA
    Posts
    1,584
    Quote Originally Posted by Jim Matthews View Post
    I prefer "Slipit" for wood on wood moving parts.

    No discernible residue, doesn't attract sawdust.
    Apply with a small toothbrush - a little goes a long way.

    https://www.amazon.com/Grizzly-G5562.../dp/B0000E6TJ8
    Another vote for slipit, it’s essentially just paraffin with a little bit of solvent to make it a paste but much easier to apply than using a bar of wax.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •