-
Will be adding a thin strip along the bottom edges, so things don't go sliding around...
One door has all the plugs done...needed to trim them flush..
Door plugs, plug trimmers.JPG
Bevel down with the chisel, doesn't take much of a hammer ( and saves my hand) and a Stanley No. 60-1/2 to finish the job..
Door plugs, plugs trimmed flush.JPG
Witch's Brew has been mixed, and applied to the one door..
Door plugs, Witch's Brew colour.JPG
Still need plugs made for the other door...about 11 after this one..
Door plugs, #14 out of 25, right side.JPG
Number 14..out of 25.
Will do the tour this weekend...should be close to done...
-
Steven,
I think your famous "Witches Brew" is going to do the trick, from the look of the first door, and the plugs turned out pretty good too.
Stew
Last edited by Stew Denton; 04-02-2020 at 10:15 PM.
-
Just bought a pair of latches...$3.80 for the pair.
need to mill 1 more plugs, install them, trim all 25 plugs flush, and then the Brew applied....then add the brass plated latches....
-
Let's see...Latches?
Tool door, latches.JPG
Irwin screw starter to start the holes...
Tool Cabinet doors, screw starter.JPG
Install latches so they pull the doors shut, and tight..
Tool Cabinet doors, latches installed.JPG
Mill 11 plugs, and install...trim flush, sand smooth..
Tool Cabinet doors, plugs completed.JPG
Ouside of the door was given a coat of that Famous Witch's Brew...and wiped down..
The Five Cent Tour, full frontal.JPG
Looks like we are about done?
The Five Cent Tour, open for business.JPG
And open for Business?
Getting the Five Cent Tour about ready to go....
-
The $0.05 Tour has begun...
The Five Cent Tour, full frontal.JPG
Start here...then swing the doors open...
Project Post Tour, full right side.JPG
Right side is a bit full..
Project Post Tour, Full left side.JPG
As is the Left side...Details?
Project Post Tour, hammers and drill.JPG
Egg beater drills, a few hammers, couple of block planes.
Project Post Tour, upper right corner.JPG
Upper Right corner....
Project Post Tour, Lower right corner.JPG
And the lower right corner, with a few planes...
Project Post Tour, Rogue's Gallery.JPG
Sitting in the Rogue's Gallery ( anyone you know?)
Project Post Tour. Drill rack.JPG
And, above that....a few drills...among other items...
Stay tuned, the Left side is coming right up..
-
And the left side....The Upper left corner...
Project Post Tour, upper left corner.JPG
That larger brace is a 14" sweep..for those really big jobs...Next, a little lower..
Project Post Tour, left corner 2.JPG
And the bottom of the corner..
Project Post Tour, left corner 1.JPG
two Stanley #4s....In front is a No. 4, type 10....behind that is the Stanley # 12-004c, made in England. Box has the Stanley #45, with the case for the Stanley #71-1/2, Type 4 sitting on top..
Project Post Tour, saws and things.JPG
left hand door has a few saws and chisels...and yet another block plane ( things are like Mice...)
And that will do it, for the tour.
Close the doors. First, reset the right door's prop..
Project Post Tour, door prop.JPG
Keeps that door from slamming back on me...
Hope you enjoyed the show...
-
Steven,
Nice tour. I think a lot of us are always interested in tool storage. I am for sure. l like to see posts on that subject, and I think a lot of us like builds and builds of benches, etc.
By the way, your famous witches brew Did Do the Trick! Looks good.
Thanks and regards,
Stew
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules