Results 1 to 4 of 4

Thread: Split image in corel

  1. #1
    Join Date
    Dec 2012
    Location
    Arizona
    Posts
    4,056

    Split image in corel

    Now I don't want you to do it for me but can you tell me how to do it. I've been playing with it for over an hr now . tried a few different things. can't weld it can't use delete knife, Air Pad 2.cdr I'm stuck LOL
    2 rectangles are separate . I need the logo split were the bottom portion goes into the bottom box.Air Pad 2.cdr

    OK Maybe I got it I cropped the lower half now I'll do same to top and see if it will engrave that way
    Last edited by Bert Kemp; 10-20-2019 at 8:20 PM.
    If the Help and advice you received here was of any VALUE to you PLEASE! Become a Contributor
    Rabbit RL_XX_6040-60 watt Laser engraving/cutting machine
    Lasercut 5.3
    CorelDraw X5

    10" Miter Saw with slide
    10" Table Saw
    8" bench mount 5 speed Drill Press
    Dremel, 3x21 Belt Sander


  2. #2
    Join Date
    Dec 2012
    Location
    Arizona
    Posts
    4,056
    OK I think this might work,, it was a lot of work . Mavic Pilots.jpg if theres n easier way Im all ears LOL
    Last edited by Bert Kemp; 10-20-2019 at 9:25 PM.
    If the Help and advice you received here was of any VALUE to you PLEASE! Become a Contributor
    Rabbit RL_XX_6040-60 watt Laser engraving/cutting machine
    Lasercut 5.3
    CorelDraw X5

    10" Miter Saw with slide
    10" Table Saw
    8" bench mount 5 speed Drill Press
    Dremel, 3x21 Belt Sander


  3. #3
    what you did is basically how I did it, but I only took a few seconds

    here's what I did:
    1- measured the whole thing, it's 19" wide, so I put in a 20" arrow-button jog space
    2- grouped the entire logo but not the rectangles, and hit Ctrl+Home (aka bring to front)
    3- grouped everything, hit copy, then jogged the copy once to the right, 20"--
    4- on the left graphic I grouped the top rectangle and the whole logo, then hit "FRONT MINUS BACK"
    5- on the right graphic, I grouped the bottom rectangle and the whole logo, and "FRONT MINUS BACK"
    6- the result:

    mav.jpg

    --both rectangles are there, but 'divorced' from the graphic, so they can be deleted. Then just jog the right half left one click and they're together, but separated
    mav2.jpg
    I painted the logo but left the black outline, you can see the split. If you laser only the magenta and don't run the outline, it will laser as one piece...

    There may be an even easier way, but ..?
    Last edited by Kev Williams; 10-21-2019 at 12:08 AM.
    ========================================
    ELEVEN - rotary cutter tool machines
    FOUR - CO2 lasers
    THREE - fiber lasers
    ONE - vinyl cutter
    CASmate, Corel, Gravostyle


  4. #4
    Join Date
    Dec 2012
    Location
    Arizona
    Posts
    4,056
    Thanks Kev I'll see if I can do it that way to. just to learn a new method
    If the Help and advice you received here was of any VALUE to you PLEASE! Become a Contributor
    Rabbit RL_XX_6040-60 watt Laser engraving/cutting machine
    Lasercut 5.3
    CorelDraw X5

    10" Miter Saw with slide
    10" Table Saw
    8" bench mount 5 speed Drill Press
    Dremel, 3x21 Belt Sander


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •