Results 1 to 14 of 14

Thread: Simple Jewelry Box Tutorial

  1. #1
    Join Date
    Apr 2005
    Location
    Villa Park. CA
    Posts
    13,048

    Simple Jewelry Box Tutorial

    I teach a class on making a simple jewelry box. Some time back, I did a tutorial for my students but my techniques have changed over the years so I did an updated tutorial. Many people here probably have skill levels beyond this tutorial but I'll offer it for anyone who might get something out of it. Click here.

    I also did a video tutorial but the production quality was not too good. I did learn quite a bit about doing a video, however, doing that project and any future video I do will be better.

    Mike
    Go into the world and do well. But more importantly, go into the world and do good.

  2. #2
    Thanks Mike. I am just in the midst of making a small jewelry box. I'll go see what I can learn.
    Appreciate it!
    Fred
    "All that is necessary for the triumph of evil is that good men do nothing."

    “If you want to know what a man's like, take a good look at how he treats his inferiors, not his equals.”

  3. #3
    Join Date
    Mar 2015
    Location
    SE Michigan
    Posts
    3,222
    Thanks for posting Mike. Your original tutorial was a very good intro into my box making.

    I always had a bit of trouble aligning the top and bottom perfectly to mark for hinges, so now when cutting the box open, I run a shallow kerf first and make a mark for the hinge placement across the kerf, and then finish cutting the box open. As you noted, there is usually a very minor mis-alignment that can easily be fixed with a card scraper or sandpaper.

    Also, if I’m going to felt the inside bottom, I use peel and stick felt over the entire bottom before glue up. I cut the groove to accommodate the added thickness. I wrap the entire bottom with cling wrap, then do the glue up. Doing felt this way eliminates the need to try to “fit” the felt, and the cling wrap protects the felt throughout the glueing, sanding and finishing steps. The cling wrap is easily removed by stretching it and cutting around the inside bottom edge with an x-acto, and then usually it will just pull loose from the bottom side of the bottom...if that makes sense.
    Here’s an example of one I just completed:

    F3331523-35C2-4EB0-8E8C-B67EB9A657A5.jpg
    Last edited by Phil Mueller; 09-06-2019 at 4:17 PM.

  4. #4
    Join Date
    Apr 2005
    Location
    Villa Park. CA
    Posts
    13,048
    Quote Originally Posted by Phil Mueller View Post
    Thanks for posting Mike. Your original tutorial was a very good intro into my box making.

    I always had a bit of trouble aligning the top and bottom perfectly to mark for hinges, so now when cutting the box open, I run a shallow kerf first and make a mark for the hinge placement across the kerf, and then finish cutting the box open. As you noted, there is usually a very minor mis-alignment that can easily be fixed with a card scraper or sandpaper.

    Also, if I’m going to felt the inside bottom, I use peel and stick felt over the entire bottom before glue up. I cut the groove to accommodate the added thickness. I wrap the entire bottom with cling wrap, then do the glue up. Doing felt this way eliminates the need to try to “fit” the felt, and the cling wrap protects the felt throughout the glueing, sanding and finishing steps. The cling wrap is easily removed by stretching it and cutting around the inside bottom edge with an x-acto, and then usually it will just pull loose from the bottom side of the bottom...if that makes sense.
    Here’s an example of one I just completed:

    F3331523-35C2-4EB0-8E8C-B67EB9A657A5.jpg
    Thanks for your note, Phil. That's a good idea about the felt and the cling wrap - I would have never thought of that. I'll try it. Thanks for the suggestion.

    Good looking box and nice veneer work. What brand of hinges did you use? I'm always looking for less expensive (but decent) alternatives to the Brusso.

    Mike
    Go into the world and do well. But more importantly, go into the world and do good.

  5. #5
    Join Date
    Mar 2015
    Location
    SE Michigan
    Posts
    3,222
    Thanks Mike, I can’t take credit for the cling wrap...saw it in a video somewhere...but it does work well.

    Wish I could help on the hinges...I use Brusso as well. Nothing seems to compare.

  6. #6
    Join Date
    Mar 2016
    Location
    Florida
    Posts
    1,950
    Nice tutorial Mike. Thanks for sharing. Bookmarked for later.

  7. #7
    Join Date
    Jun 2008
    Location
    So Cal
    Posts
    3,730
    Very good tutorial Mike. Box making is one of my favorite projects.
    These small quadrant hinges from Rockler are pretty inexpensive. I like them because they hold the lid up and open.
    They do take more time to install and the lid cannot be too thin.
    But I think they are worth the trouble for the box that has something special.
    Good Luck
    Attached Images Attached Images
    Aj

  8. #8
    Join Date
    Apr 2005
    Location
    Villa Park. CA
    Posts
    13,048
    Quote Originally Posted by Andrew Hughes View Post
    Very good tutorial Mike. Box making is one of my favorite projects.
    These small quadrant hinges from Rockler are pretty inexpensive. I like them because they hold the lid up and open.
    They do take more time to install and the lid cannot be too thin.
    But I think they are worth the trouble for the box that has something special.
    Good Luck
    Thanks for your note, Andrew. I've used quadrant hinges in the past - I even did a tutorial on installing them without a router. But they're too difficult and fussy - a real pain to install. The Brusso are MUCH easier to install.

    What I'd like to find is a regular leaf hinge with a stop around 90 degrees, but less expensive than the Brusso. Rockler has one for cheap and I tried them but they really cheapen the look of the box.

    The Brusso hinges I use (JB-102) are stop hinges, meaning they hold the top upright when you open the box. Early on I made a box with a removable top but my wife told me that was a problem. She said, "Where do you want me to put the top when I go into the box?"

    Mike
    Last edited by Mike Henderson; 09-06-2019 at 6:48 PM.
    Go into the world and do well. But more importantly, go into the world and do good.

  9. #9
    Join Date
    Dec 2016
    Location
    Central MN
    Posts
    42
    Excellent tutorial

  10. #10
    Mike
    Thanks for posting a great tutorial. I am a fan of box making and, as much pleasure as I take from making them, it is always rewarding to see the appreciation of the recipient.
    Mike Null

    St. Louis Laser, Inc.

    Trotec Speedy 300, 80 watt
    Gravograph IS400
    Woodworking shop CLTT and Laser Sublimation
    Dye Sublimation
    CorelDraw X5, X7

  11. #11
    Join Date
    May 2015
    Location
    Ingleside, IL
    Posts
    1,417
    Thanks Mike - great tutorial.
    Stand for something, or you'll fall for anything.

  12. #12
    Join Date
    Apr 2017
    Location
    Michigan
    Posts
    2,755
    Awesome tutorial Mike. I picked up many tips. Just have one to offer in return.

    Instead of clamping the top and bottom with spring clamps which can cause movement and possible warping, use "gravity clamps". Just set it on a flat surface and add cauls and weights. By adding several smaller weights one at a time you will have very little risk of squirm.

  13. #13
    Join Date
    Dec 2012
    Location
    Bedford, NH
    Posts
    1,286
    Well done Mike - nice details!

    Boxes have always been my favorite projects for gifts. I've always had concerns about holding the sides "tightly" against a miter gauge to prevent sliding while cutting the mitered ends. I like to use a TS sled with clamped blocks for a more positive stop to prevent sliding and to duplicate dimensions.

    Phil, that is a really good ide. I will use that one for sure, especially since i've had a very large roll of cling wrap that I never used.
    Thoughts entering one's mind need not exit one's mouth!
    As I age my memory fades .... and that's a load off my mind!

    "We Live In The Land Of The Free, Only Because Of The Brave"
    “The problems we face today are there because the people who work for a living are outnumbered by those who vote for a living."
    "
    Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery." Winston Churchill

  14. #14
    Join Date
    Apr 2005
    Location
    Villa Park. CA
    Posts
    13,048
    Quote Originally Posted by Tom Bender View Post
    Awesome tutorial Mike. I picked up many tips. Just have one to offer in return.

    Instead of clamping the top and bottom with spring clamps which can cause movement and possible warping, use "gravity clamps". Just set it on a flat surface and add cauls and weights. By adding several smaller weights one at a time you will have very little risk of squirm.
    Thanks for your note, Tom. I'll try your idea of the weights next time I do a box.

    Mike
    Go into the world and do well. But more importantly, go into the world and do good.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •