Results 1 to 5 of 5

Thread: Burnishing A Burr On Scrapers

  1. #1
    Join Date
    Feb 2017
    Location
    Northern Illinois
    Posts
    459

    Burnishing A Burr On Scrapers

    Recently I attempted to burnish a burr on a round scraper I had just sharpened on a 600 grit diamond Tormek wheel. The angle I use is approximately 70 degrees. I found that the burr, after burnishing it, wasn't as effective as the burr I got after merely sharpening on the Tormek. This leads me to assume I'm doing something wrong when burnishing.

    Questions -

    1. When burnishing, should your hand holding the burnisher be toward the beveled part of the scraper or the flat side?
    2. Is there angle to use as a goal to get an optimum burr?

  2. #2
    I can't remember for sure, but I think I cover that in my platform sharpening video. So, for burnishing a burr on high speed steel, your burnishing tool needs to be harder than the steel. With the standard burnishing rods for the card scrapers, they may be a tiny bit harder, and don't work all that well. I did better with the triangular shaped one than I did with the round ones. I now use a small diameter carbide rod for burnishing. There is also a tool from Lee Valley/Veritas tools that screws down to your bench top and it has carbide rods, but I prefer hand held because I use a lot of different angles, and some tend to apply too much pressure when using this tool. There are carbide rods available on the internet, or old router bits can work well also. All it takes is a couple of light strokes across the bevel. The angle you should use, for a 70 degree bevel scraper would be 5 to 10 degrees more than that. If you have the burnishing rod at a much steeper angle, you can actually turn the burr over so it barely cuts unless you really raise the handle for roughing or end grain cuts, or roll the tool way over on the side for shear scraping. I do all of my roughing cuts on bowls with a grinder burr and the Big Ugly tool. For shear scraping, I prefer a fresh edge and most of the time I will turn/burnish the grinder burr down, then back up. If I am doing finish cuts in end grain boxes, I will hone the grinder burr off, then burnish a light burr up on that. I do burnish my NRSs also. I have found that a 60/30 NRS burnishes up with a little less effort than on a 70/30 NRS, and I have tried to burnish one on an 80/30 'hardwood bowl NRS' from Sorby tools, and found that difficult.

    robo hippy

  3. #3
    Join Date
    Feb 2008
    Location
    E TN, near Knoxville
    Posts
    8,099
    Quote Originally Posted by Randy Heinemann View Post
    Recently I attempted to burnish a burr on a round scraper I had just sharpened on a 600 grit diamond Tormek wheel. The angle I use is approximately 70 degrees. I found that the burr, after burnishing it, wasn't as effective as the burr I got after merely sharpening on the Tormek. This leads me to assume I'm doing something wrong when burnishing.

    Questions -

    1. When burnishing, should your hand holding the burnisher be toward the beveled part of the scraper or the flat side?
    2. Is there angle to use as a goal to get an optimum burr?
    I hold the burnisher in my right hand with the scraper bevel to the right. The angle is just a few degrees - I lay the burnisher against the bevel then raise the lower end a little off the bevel. Some advocate starting with just a degree or so of angle then increasing the angle with each of several successive passes.

    Another way is to put the scraper in a vise and use two hands on the burnisher for more pressure. Card scrapers are often laid flat on the workbench with the edge off the table a bit and burnished with the burnisher held a few degrees off vertical.

    The angle, the pressure used, and the number of passes with the burnisher depends on the radius of the burnisher and how aggressive I want the edge. A small radius burnishing rod will create a larger burr with the same pressure. A triangular burnisher effectively has a very small radius. My burnishers are carbide but I have used the side of a HSS gouge in a pinch.

    After burnishing you should be able to feel the burr when dragging your finger across the top face of the scraper or across the upper bevel of a negative rake scraper. If it doesn't cut as well as I want I burnish again with more pressure. I've experimented a lot over the years to come up with the angle and pressure I use. I don't know of any easy way to tell someone else other than to suggest just trying things.

    Note that before burnishing I almost always remove any grinder burr with an extra fine diamond hone.

    The Veritas burnisher Reed mentioned can be quite aggressive with minimum effort - the angle is fixed but should be fine for a 70-deg flat-topped conventional scraper. Not useful for the negative rake scrapers I almost always use now. https://www.woodturnerscatalog.com/p...aper-Burnisher

    I just remembered I wrote about burnishing in a thread a few months ago. It was about negative rake scrapers but the principle is the same.

    https://sawmillcreek.org/showthread....13#post2910113

    JKJ

  4. #4
    Join Date
    Feb 2017
    Location
    Northern Illinois
    Posts
    459
    Still a little confused (but that is a problem sometimes) . . . I am using the carbide rods I got from you so that shouldn't be an issue.

    What I'm unclear about is when you say "5 to 10 degrees more than" the scraper bevel. Does that mean the burnishing angle should be be 80 degrees or 60? I'm not sure how to ask the question clearly.

  5. #5
    Join Date
    Feb 2017
    Location
    Northern Illinois
    Posts
    459
    I think I understand why my first effort wasn't very successful. I will experiment with a little better understanding now. Thanks to both Reed and John.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •