Results 1 to 5 of 5

Thread: Fiber laser bonded aluminum to glass.. what did I actually do?

  1. #1

    Fiber laser bonded aluminum to glass.. what did I actually do?

    Hey Folks..

    I was fooling around experimenting today and I put a piece of glass on the bed covered the surface with perm marker and set it on an aluminum plate.

    Default settings (200mms/100% power (20 watts, fiber laser) and 20khz) and burned a cm square block.

    When I picked the glass off, a layer of aluminum had fused to the back of the glass. I even tried to scrape of off.. I COULD, but in short, it was there permanently. The glass was pretty rough in the first place, but the alum was nicely coated and pretty specific to the prescribed burn point.

    I ASSUME I performed some sort of vapor deposition or something?

    But.. what DID I do? (not a trivia question.. I'm honestly curious)

  2. #2
    Join Date
    Mar 2014
    Location
    Iowa USA
    Posts
    3,347
    Quote Originally Posted by Morgan Jackson View Post
    Hey Folks..

    I was fooling around experimenting today and I put a piece of glass on the bed covered the surface with perm marker and set it on an aluminum plate.

    Default settings (200mms/100% power (20 watts, fiber laser) and 20khz) and burned a cm square block.

    When I picked the glass off, a layer of aluminum had fused to the back of the glass. I even tried to scrape of off.. I COULD, but in short, it was there permanently. The glass was pretty rough in the first place, but the alum was nicely coated and pretty specific to the prescribed burn point.

    I ASSUME I performed some sort of vapor deposition or something?

    But.. what DID I do? (not a trivia question.. I'm honestly curious)
    Well you might have discovered a new process.
    Retired Guy- Central Iowa. , LightObject 40w CO2 Laser and Chiller, MakerGear M2 3D Printer. Fine Line Automation 4x4 CNC Router- Mach4 ESS

  3. #3
    Join Date
    Dec 2010
    Location
    NW Arkansas
    Posts
    1,516
    I figure the aluminum 'cut' from the sheet was hot enough to slightly melt the glass and as you said inbed itself in the glass plate. metal is sparked off at pretty high temp by these things
    Woodworking, Old Tools and Shooting
    Ray Fine RF-1390 Laser
    Ray Fine 20watt Fiber Laser
    PM2000, Delta BS, Delta sander, Powermatic 50 jointer,
    Powermatic100-12 planer, Rockwell 15-126 radial drill press
    Rockwell 46-450 lathe, and 2 Walker Turner RA1100 radial saws

    RIA 22TCM 1911s

  4. #4
    ^^ What John said ^^

    1064nm lasers pass right thru glass, and they turn aluminum into molten goo near immediately, definitely hot enough to melt glass...
    ========================================
    ELEVEN - rotary cutter tool machines
    FOUR - CO2 lasers
    THREE - fiber lasers
    ONE - vinyl cutter
    CASmate, Corel, Gravostyle


  5. #5
    Join Date
    Aug 2006
    Location
    Suwanee, GA
    Posts
    3,590
    I've done that with brass, works pretty well actually. It wasn't long after I got my first fiber and I didn't have a need for it so I didn't save the settings, but I believe it was 100% power and probably 40f, 500s.
    I have done so much with so little for so long, that I can do almost anything with practically nothing...

    Trotec Speedy 400 80 watt 8/2015
    G. Weike LF-30, 30 watt galvo fiber - 1/2016
    G. Weike LF-30, 30 watt galvo fiber - 3/2015
    Fargo HDP5000 Card printer


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •