Curious if anyone has used both Cermark spray vs. paste
Have a preference?
Any pros/cons to either?
Curious if anyone has used both Cermark spray vs. paste
Have a preference?
Any pros/cons to either?
Trevor Bittinger
Epilog Mini 24 - 40 watt
NO, paste only. Do a search and you can see a lot of comments. But on other sites, a LOT of folks have issues if you let the spray sit without use for a while, clogs badly. And per area, way more expensive.
It is way easy to mix up a batch (I do small amounts at a time) with some DNA and spread with a foam brush. I've been using 6000 lately and it spreads out really well with good coverage. And engraves Flatter for me.
I used LMM14 for a year, works great, can be a bit streaky once applied, but it doesn't show it once engraved. (as long as there is some coverage over the surface). BUT you are single use on foam brush, 14 will eat it.
I used a small acid brush to apply it. On a very large surface I would have gone to foam brush.
Woodworking, Old Tools and Shooting
Ray Fine RF-1390 Laser Ray Fine 20watt Fiber Laser
SFX 50 Watt Fiber Laser
PM2000, Delta BS, Delta sander, Powermatic 50 jointer,
Powermatic 100-12 planer, Rockwell 15-126 radial drill press
Rockwell 46-450 lathe, and 2 Walker Turner RA1100 radial saws
Jet JWS18, bandsaw Carbide Create CNC, RIA 22TCM 1911s and others
I use both, but prefer paste with a brush. It's fast, efficient, and seems to go a LOT further than the spray.
Tim
There are Big Brain people & Small Brain people. I'm one of the Big Brains - with a lot of empty space.- me
50W Fiber - Raycus/MaxPhotonics - It's a metal eating beast!
Epilog Fusion M2 50/30 Co2/Fiber - 2015
Epilog Mini24 – 35watt - 2006 (Original Tube)
Ricoh SG3110DN
- Liberty Laser LLC
Thanks guys. I had already ordered some spray to give it a shot right before I posted this, so decided to test it out and give it a go on some steel. First spray application went fine, but then a few hours later, tried it again and it got stuck and ended up spraying/emptying itself all over the place. I've requested a refund from Johnson Plastics and will be using the paste only from here on out. Thanks again for your helpful replies.
I had my settings at 600dpi, 25s, 100p and it still didn't mark it as super black. I'm using a 40watt C02 laser.
IMG-3778.jpgIMG-3776.jpg
Trevor Bittinger
Epilog Mini 24 - 40 watt
for all you guys/gals who've used or still use spray cans, don't throw 'em away, as there's sometimes LOTS of Cermark still sitting in the bottom! Poke a hole in the top of the can to release the pressure, then hacksaw the can in half about 1/3 the way down the can. In the bottom you'll find the leftovers-- scoop it out and mix it with denatured alcohol until it's thin enough to brush. I've gotten as much as 3oz of re-mixed from an 'empty' can! I typically generate $400 or so per ounce of premix, so it's worth going after!
(And I would be for carefully scraping all that Cermark off that cardboard into a storage bucket too!)
========================================
ELEVEN - rotary cutter tool machines
FOUR - CO2 lasers
THREE- make that FOUR now - fiber lasers
ONE - vinyl cutter
CASmate, Corel, Gravostyle
If you don't need to handle the part too much after you coat it with cermark, then try the LMM14. I use it exclusively now and won't go back to the LMM6000. I get 99.9% out of the can, the tip won't clog from non use and it makes just as black of a mark. Just be careful b/c if you touch it, it will come off.
Also.....Welcome back Kev.
Universal 60w VLS6.60 w/ rotary
RayFine 30w MOPA
Corel X8, Photoshop
Fab shop with South Bend Heavy 10, Bridgeport 9x42, 185a welder and a multitude of supporting tools/equipment
I'm not gone, just whacking my online time down a ton (it's helped!)
========================================
ELEVEN - rotary cutter tool machines
FOUR - CO2 lasers
THREE- make that FOUR now - fiber lasers
ONE - vinyl cutter
CASmate, Corel, Gravostyle
Tim
There are Big Brain people & Small Brain people. I'm one of the Big Brains - with a lot of empty space.- me
50W Fiber - Raycus/MaxPhotonics - It's a metal eating beast!
Epilog Fusion M2 50/30 Co2/Fiber - 2015
Epilog Mini24 – 35watt - 2006 (Original Tube)
Ricoh SG3110DN
- Liberty Laser LLC
Problem might be your lens.
The top line on this plate was done with my new-to-me (3-ish year old) LS100 Gravograph 35w laser...
lt1.jpg
It's gray, the other 3 lines are black... Lines 2 and 4 were done with my LS900 40w laser,
line 3 was done with the LS100 using the LS900 lens, no other changes. It's black...
Not shown on this piece, I put the LS100 lens in the LS900, and got gray Cermark, with no other changes.
Strictly a lens issue. I'm currently waiting on new 'test' lenses.
========================================
ELEVEN - rotary cutter tool machines
FOUR - CO2 lasers
THREE- make that FOUR now - fiber lasers
ONE - vinyl cutter
CASmate, Corel, Gravostyle