Results 1 to 8 of 8

Thread: Travel Mug Epoxy

  1. #1
    Join Date
    Mar 2018
    Location
    Anchorage, AK
    Posts
    20

    Travel Mug Epoxy

    Howdy folks,

    I recently turned a batch of stainless insert mugs, and had a funny thing happen. After epoxy set, and I filled the mug with coffee, I heard a popping sound. I assume the epoxy is reacting with the heat from the coffee.

    If this is so, do you guys have a recommendation on a better epoxy to make my product better?

    Cheers,

    Jed

  2. #2
    Join Date
    Dec 2012
    Location
    Bedford, NH
    Posts
    1,286
    Ice coffee? Sorry, couldn't resist.
    Thoughts entering one's mind need not exit one's mouth!
    As I age my memory fades .... and that's a load off my mind!

    "We Live In The Land Of The Free, Only Because Of The Brave"
    “The problems we face today are there because the people who work for a living are outnumbered by those who vote for a living."
    "
    Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery." Winston Churchill

  3. #3
    Join Date
    Feb 2007
    Location
    Inver Grove Heights, MN
    Posts
    798
    Heat will soften epoxy, but I believe it takes more than you would get from coffee. I also can't think of what would make a popping noise if the epoxy just softened a little. Did anything let go or fall off? Is this a staved cup or turned from one piece of wood? What was the epoxy used for? Sorry about the questions, but you got me curious. All my cups have been turned from one piece of wood and I have had one or two crack with use. I assumed that it was because I didn't use kiln dried wood.

  4. #4
    Join Date
    Mar 2018
    Location
    Anchorage, AK
    Posts
    20
    The mugs are both, staved, and segmented. Popping from both. The epoxy I used was the cheap 5 minute kind from the local box store. I turned all of them to 1/8" wall thickness, and applied a quarter sized amount of epoxy to the side walls of the stainless, and seated it in the wood. There are no cracks in the wood whatsoever. The popping only lasts for 1.5 seconds or so.

  5. #5
    Join Date
    Feb 2007
    Location
    Inver Grove Heights, MN
    Posts
    798
    Is it possible that it has nothing to do with the epoxy. The heat causes the air between the steel liner and the wood to expand. The top is constrained by being fastened to the steel liner, so the wood itself bends causing the popping noise. It is a strange one Jed. I hope there is at least one other poster who has experienced something similar.

  6. #6
    Join Date
    Mar 2018
    Location
    Anchorage, AK
    Posts
    20
    Good call. Pending any trapped air spots, a weep hole in the bottom should alleviate this, I think. I'll try that.

  7. #7
    Join Date
    Feb 2008
    Location
    lufkin tx
    Posts
    2,054
    The SS metal will be affected by heat but not the wood or epoxy to any significant extent.

  8. #8
    Join Date
    Sep 2014
    Location
    Strongsville OH
    Posts
    113
    In Malcolm Tibbetts article in 2007 American Woodturner, he recommends silicon adhesive to glue the insert to the wood at the top. He also uses Gorilla glue on the entire insert surface, after it expands it acts like an insulating foam. I have followed his practice and I don't hear any noises.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •