Just because the lumber was dimensioned and flat when you stocked it doesn't mean it is now. Even under the best of storage conditions wood moves. It should be final dimensioned as soon before it's needed as practical.
Just because the lumber was dimensioned and flat when you stocked it doesn't mean it is now. Even under the best of storage conditions wood moves. It should be final dimensioned as soon before it's needed as practical.
Bill what exactly are you looking for help with ? I think you have gotten the advice you need,figure out what you want to build and buy a tool you need for that job,repeat. This is how everyone I know has built their collection of tools and machines and the area they work in. Woodworking is like a living organism it breathes and changes and switches directions etc. Everyone has their own path down this "road". Sounds like you are into wood turning and are working out from there ,so if it was me I would look at a bandsaw. Good luck "finding your way",Mike.
A bandaw or a planer would my next purchase. Both get used a great deal in my shop.
Paul
Heater and connections for it.
Glad its my shop I am responsible for - I only have to make me happy.
Just reread your first post, do you have a bench of any type yet ? If not start with that.
Last edited by Bill Dufour; 01-06-2018 at 11:48 PM.
You said power or hand tools. I would suggest investing in good quality measuring and layout tools. Start with a Starrett 12" square.
I second the recommendation of a bench. A solid bench is a must-have for any work with any tools, especially hand planes. A decent face vise (Record type) is also essential. Look up work holding methods.
Beyond these, you need to decide on what you plan to build, and get the tools for that project. Don't be daunted - the art of woodworking is the work-around. Personally, I would look at a few hand planes, such as Stanley #4, #5 and #7. It sounds as though you already have a block plane. Oh ... do you have chisels?
Regards from Perth
Derekg
Purchase what you need as you need it.
Get excited to build something and start working out what you need to build it. Get what you need that you dint already have and build it.
Keep building projects on a consistent basis and before you know it you will have a fully operational shop.
I agree with Derek. Wood working is all about work arounds, there is more than “one way to skin a cat” as much as I don’t care for the saying.
When I started building a proper shop I already had a full arsenal of site based tools. I could for the most part build anything I wanted all be in a pita other than dimension lumber. I purchased a piece of junk dewalt planer and a 100 year old 6” jointer. I used those for one project before I decided no way was I going to build anything ever again with those two tools. The jointer had zero dust collection and the planer might of well had no dust collection either. Both the dewalt did such a poor job planing I decided I needed to save my pennies for a proper jointer and planer.
I saved for about a year and purchased a 16” combo and a 5hp dust collector. These two or three purchases changed everything. I then purchased a band saw then a cabinet saw, then a shaper, then a slot mortiser, then drill press, then another band saw. You get the point, once the jointer/planer/table saw/dust collector purchases where behind me buying the tools as needed as the project called for them was painless by comparison.
I have been knee deep in hand tool purchases for a couple years now. The plan has been at least for me when the hand tool purchases are done for the most part to upgrade my ts to a slider and add a second shaper.
On the flip side for the most part I could do anything back with a job site table saw, track saw, crappy jointer/planer as I will be able to do with a 50K slider and $30-50k shaper. It’s just much much more easy to get a good result in a reasonable period of time with the later tools. And it’s much more enjoyable using your tools rather than spending all your time fettling with them trying to get them to work right or cleaning up after the mess they make.
My point remains. Get excited to build something. Figure out how your gonna do that, what your gonna need and get to it.
Frankly I think with the amount you have set aside to spend you are basically limiting yourself to hand tools As noted above a band saw is very useful, but is outside your price range. Given that you might consider a quality jigsaw as a substitute until you can get a band saw. You could also consider a set of chisels, hand held belt sander, set of files, can never have enough clamps.
Thoughts entering one's mind need not exit one's mouth!
As I age my memory fades .... and that's a load off my mind!
"We Live In The Land Of The Free, Only Because Of The Brave"
“The problems we face today are there because the people who work for a living are outnumbered by those who vote for a living."
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery." Winston Churchill
Thanks for all the suggestions.
I mentioned a plane in my original post and I may go that way.
It's bitterly could here so a heater would light a fire under me. Hard to drum up the ambition to work with any tool at below freezing.
You are a great community, Sawmillcreek.