Anyone have a source for exotic ribbon cable ends...... Hard to pay $85 for a cable that only needs a $2 end.
20 wire ribbon cable
.
Anyone have a source for exotic ribbon cable ends...... Hard to pay $85 for a cable that only needs a $2 end.
20 wire ribbon cable
.
Mark
In the Great Northwest!
Trotec Speedy C25, Newing-Hall 350 (AMC I & HPGL), NH-CG-30 (Carbide Cutter Sharpener)
Sawgrass 400 Gel Ink Printer, CS5, 5/9/x6 CorelDraw
Mark,
Check your local electronics parts distributor.
Otherwise, Digykey would have them.
Check this place-------------
http://www.vetco.net/catalog/
Last edited by Tony Lenkic; 05-19-2016 at 3:17 PM.
Trotec Speedy 300 - 60w, with Quatro CSA-626 fume extraction
Xenetech 1625 x2,
New Hermes TX pantograph, CG4 cutter grinder
Brady Globalmark2 label printer,
Assortment of custom tooling , shears & punches, heat bender.
Software: Xenetech XOT, Corel X3, Bartender label software
Thanks Tony.... That is my local distributor. If they have them they are under a desk in a box with dust on them.. Nothing in the Catalog even close except a generic IDC Connector for ribbon cable.
Mark
In the Great Northwest!
Trotec Speedy C25, Newing-Hall 350 (AMC I & HPGL), NH-CG-30 (Carbide Cutter Sharpener)
Sawgrass 400 Gel Ink Printer, CS5, 5/9/x6 CorelDraw
How about Mouser? I did a quick search on there and saw a few that looked like they would either work or could be modified to work.
Also - if you send them a photo of the cable end, they will search for you and tell you what part number to buy.
4 - Q1 converted New Hermes C2000's
Signature 8080 Plus
Universal 50w X2-600
Universal 60w X-660
Epilog 60w Fusion 40
50w 5070 China Special
Thanks Brain I'll give them a try....... Looking at European websites and getting closer....Found one in China (100 min)...
Ordered a style match from Mouser... will see if it is a good match...
Thanks..
Last edited by Mark Sipes; 05-19-2016 at 6:14 PM.
Mark
In the Great Northwest!
Trotec Speedy C25, Newing-Hall 350 (AMC I & HPGL), NH-CG-30 (Carbide Cutter Sharpener)
Sawgrass 400 Gel Ink Printer, CS5, 5/9/x6 CorelDraw
Not sure if this is exactly what you need, but here is where you need to look anyway: digikey has all types of sizes of ths free-hanging rectangular connector.
http://www.digikey.com/product-detai...IDC-ND/5050384
Matt
Matt you are correct.... Just wish I did not have to order 84 of them as a min quantity.
Mark
In the Great Northwest!
Trotec Speedy C25, Newing-Hall 350 (AMC I & HPGL), NH-CG-30 (Carbide Cutter Sharpener)
Sawgrass 400 Gel Ink Printer, CS5, 5/9/x6 CorelDraw
Here you go- buy one of them for $3.84 : http://www.digikey.com/product-detai...146-ND/5051783
and it's pair, in case you want to replace both ends: http://www.digikey.com/product-detai...118-ND/5011309
a note on these- cut the cable cleanly so you start with a fresh end when you pierce the connector onto the cable. And when you squeeze the connector closed use a vise, or something else that will squeeze it nice and square.
Matt
Last edited by matt stott; 05-20-2016 at 2:30 PM.
I would defiantly remake that with standard 2x10 pin connectors.
Male header:
http://amzn.com/B00BUGONKG
and female socket:
http://amzn.com/B00B2ZCHB2
Last edited by Tristan Ranatza; 05-20-2016 at 5:41 PM. Reason: Edit for amazon links
try allied electronics they have all kinds of end like that also check out automation direct they should also have them