Painted Aluminum Cake Pan Lid

[Dee Gallo]

Since I cannot get anymore Doughmakers lids, I decided to try painting my own. I got some Mirro aluminum pans and painted the lid.

Thinking I should prime it first, I used a sandable red primer (which I had on hand) and bought some auto spray paint. Everything went as planned until...

I lasered the design using anodized settings (100sp/80p) since I did not know what the paint settings should be, so I started there. To my surprise, the paint came off clean but the primer remained. Looked nice, tucked that away for another time when I might want two colors... I took this picture before the second pass to avoid moving it.

I did a second pass and the primer was not even touched. Won't move.

So, as usual, I've gotten a new piece of information. I will try doing one with no primer since I like the silver look for the engraving.

Anyone know anything about metal primers?

cheers, dee

[Mike Null]

Dee

Don't be so modest. I know this was a plan, not an accident.

Your pan looks great!

[Dan Hintz]

I'm with Mike... best looking accident I've seen...

[Dee Gallo]

Thanks guys - now all I have to do is locate different colored primers, or I'll have to come up with red, white and blue design schemes. Of course, red, white and green are good for Christmas. And red, white & black is the new favorite kitchen design scheme... hmmmm

[Dan Hintz]

Dee,

There's nothing necessarily special about metal primers, other than some ingredients to convert any oxides (e.g., rust) into the corresponding metal's salt... depending upon the type of primer, it may have a higher metal content than usual (like zinc for further rust prevention), so that may have an effect on lasering it off.

On a side note... assuming this will be near food at some point, I would suggest baking the lid on low heat for an hour or so to remove any volatiles left in the paint (auto paint, especially).

[Dee Gallo]

Thanks for that suggestion, Dan. Even though the top is not supposed to be used in the oven, it will be used to cover food, so better safe than sorry.

dee

[Chuck Stone]

I made some clocks out of old saw blades and found the same thing
that you did. I used various primers and a motor paint I found on sale.
Looked great and the paint lasered well .. but the laser wouldn't touch
the primers at all. I only went down to about 10% speed .. lower than
that and I just couldn't afford the 2 hours it would take to do them.

[Dee Gallo]

Well, I made one without primer and the truth is the primer really makes the design pop. It gives the engraving some dimension, too. I coated it with lacquer to seal the primer and that really makes it look great. It reminds me of tooled leather. The unprimed one is nice, but boring next to the two color job. With some planning, you could make several colors on one design no problem.

I would do an outline of the design and burn it onto the metal, then spray with the primer colors I want in whatever place. Then a coat of the final paint and press go!

So, that's what I will be using from now on. It would be handy for making signs too or anything else needing metal as a base.

Here's a picture of it with the lacquer.

dee

[Roy Nicholson]

That's a great one for your repertoire.


Regards


Roy N.

[Mike Null]

Dee

You're right about the 3d look. Plus, you're a pretty good photographer.

Thanks for sharing some neat stuff!

[Chuck Stone]

ok, now I have to go try this..

[Dee Gallo]

I decided to make a sampler, to compare on the same piece what happens with different colored primers and paints. Rather than waste a baking pan, I used a spare metal tin.

I painted white primer, red, and black in thirds on this tin. Then, I sprayed auto paint over it making two color blocks. This should have given me 6 samples of color combinations.

I put it in the laser and used the same settings as before, but the burn went down to the metal! I lowered the power from 80 to 40 and still...metal! A tiny ghost of the primer shows through, but not much.

Can it be that steel reacts THAT differently? If the primer cannot be lased on aluminum, why can it be done on steel?

I'm flummoxed... and I would like to to have predictable results!

Thanks to anyone who can sort this out. Please forgive the obvious use of clipart, for expediency sake.

cheers, dee

[Dan Hintz]

Dee,

There's always the possibility of a reaction between different substrates and the primer (I would need to know what's in the primer to be sure), but I don't think that's the case here. So, my first question is... how consistent were you with the thickness of primer sprayed between your last sample and this one? If you became more proficient at spraying, you may have laid down a thinner coat, leading to it being more easily lasered off.

[Dee Gallo]

I'm doing another test, Dan. I just put 4 coats of primer on the bottom of the tin, and tomorrow I'll try out the laser on it to see if it makes a difference. Thanks for the boost.

BTW- I hope we don't lose you to the CNC forum now that YOU WON THE STINGERRRRR!

dee

[Mike Null]

Dee

I would try lowering the power even more on the steel.