Search:

Type: Posts; User: Dennis Peacock; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.50 seconds.

  1. Creeker's Past Week's Accomplishments

    9 Dec 2019

    Greetings,
    Been working at the day job like crazy AND I've been working on this dining table project. FINALLY got the base finished and got the top glued up!!!! Now comes the task of...
  2. Creeker's Past Week's Accomplishments

    2 Dec 2019

    Greetings,
    I hope each of you had a good Thanksgiving holiday with family and friends. I spent the week oncall duty and work most of Wednesday night, Thursday, and Thursday night. The...
  3. Replies
    3
    Views
    141

    Happy Thanksgiving to all my SMC friends and...

    Happy Thanksgiving to all my SMC friends and woodworkers!!!!
  4. Replies
    45
    Views
    1,965

    Jointing 13 ft long 8/4 lumber

    If you were building a dining or kitchen table out of 8/4 lumber, how would you joint the edges so they mate well with the other boards? Let's also add in that each board weighs in at around 100...
  5. Replies
    27
    Views
    1,844

    You will never get my Festool tracksaw and rails...

    You will never get my Festool tracksaw and rails away from me! To me, they were a real game changer when it came to complicated cuts as well as a much easier way of breaking down sheet goods. Love it!
  6. Replies
    9
    Views
    289

    OK, so looks like I'll need to order some...

    OK, so looks like I'll need to order some materials. I'm not afraid to spray a finish. I've done considerable spray finishing since I've been doing woodworking. I'll look into the EM-9300 + catalyst.
  7. Replies
    9
    Views
    289

    Dining table clear coat....

    Table top is 42" wide by 144" long and is 6/4 white oak.
    Color will be medium walnut by Minwax.
    I'm asking for advice on clear coat for the table.
    I used Marine Spar Varnish for my own kitchen...
  8. Creeker's Past Week's Accomplishments

    25 Nov 2019

    Greetings,
    It's been a crazy week at the day job and in the woodshop. Making some good progress on the dining table project.
    420283

    The base is 106" long and stands 27.5" tall....
  9. Replies
    29
    Views
    1,322

    David, Yes....I've ordered T-Nuts, screws, and...

    David,
    Yes....I've ordered T-Nuts, screws, and washers. My plan is to secure a secondary waste board on top of the factory supplied waste board and machine the t-nuts and holes in that piece without...
  10. Replies
    29
    Views
    1,322

    I've ordered t-nuts, screws and washers off...

    I've ordered t-nuts, screws and washers off Amazon and I've found some SVG files for clamps and one for a spoil board for t-nuts. I'm hoping to be "up and running" by very early next week.
  11. Replies
    42
    Views
    1,761

    Yea...I saw that....I'm now ignoring F360.

    Yea...I saw that....I'm now ignoring F360.
  12. Replies
    29
    Views
    1,322

    I Am So New To This.....that I squeak when I...

    I Am So New To This.....that I squeak when I walk!!!! My machine is now moving around and I did the Hello World job with the Sharpie pen. All is well so far except for tweaking the X axis drag chain....
  13. Creeker's Past Week's Accomplishments

    18 Nov 2019

    Greetings,
    Been a very busy week with the dining table project in full swing and getting Christmas orders done....but.....I still had time to get this put together and tested. :) ...
  14. The table top will actually be 42" wide x 1.5"...

    The table top will actually be 42" wide x 1.5" thick....solid white oak. I have 3 white oak boards that will go in this top that weigh in at 110 lbs each. The top is estimated to weigh about 350 lbs...
  15. This makes a lot of sense to me! Thank you!

    This makes a lot of sense to me! Thank you!
  16. Leg member width is 3.5" wide In short.....the...

    Leg member width is 3.5" wide

    In short.....the width at the TOP of the leg section is 34" wide.
    The width at the BOTTOM of the leg section is 34".
    The height of the leg section from the floor to...
  17. Math Question - What Difference Does 1 Degree Make?

    Ok, I'm asking here because I KNOW there's a lot of smart people here. :)

    Table base leg set - X shaped for farm style table.
    Leg Overall height - 27.5"
    Leg Overall width - 34"
    Leg...
  18. Creeker's Past Week's Accomplishments

    11 Nov 2019

    Greetings,
    The good news is that I'm making things in the shop again. The hard news is that people are falling in love with things I make and now I'm crazy busy! :)

    My Shapeoko 3...
  19. Delivery is scheduled for tomorrow! I took the...

    Delivery is scheduled for tomorrow! I took the day off from work in case they need my help. :D :D
  20. Replies
    31
    Views
    1,542

    Love it! Looks like you're keeping that CNC...

    Love it! Looks like you're keeping that CNC machine busy. ;)
  21. Creeker's Past Week's Accomplishments

    4 Nov 2019

    Greetings,
    It's been a busy oncall week and weekend and I'll be a free man once again in just over 12 hours.

    I've been busy in the shop this week when work allowed. I also pulled...
  22. Yes and yes.... BUT.....You DID win the heart...

    Yes and yes....

    BUT.....You DID win the heart of The LOYL for it. :)
  23. Order is placed!!!! Now we wait. :) I'm...

    Order is placed!!!! Now we wait. :)

    I'm working to get the shop ready for the arrival but I also have projects to get done before it arrives. So Excited!!!!
  24. I'm looking at pulling the "trigger"

    On a Shapeoko 3 XXL machine.
    I got to use one at the local "MakerSpace" at the local college. It's not a CAMaster Stinger or Panther, but it will get me started in the CNC Router world of wood that...
  25. Creeker's Past Week's Accomplishments

    28 Oct 2019

    Greetings,
    I've fallen into the pit of tablesaw repairs.
    418387

    For some strange reason, my tablesaw, drill press, and the sander I was rebuilding all decided they wanted new...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4