Search:

Type: Posts; User: Marcus Waddell; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    37
    Views
    8,783

    Another question: For super close cuts with the...

    Another question: For super close cuts with the Incra fence have you ever had any worry that the brake will be set off?
  2. Thanks...that really helps!

    Thanks...that really helps!
  3. Hey Chris: (I know this thread is old, but I'm...

    Hey Chris: (I know this thread is old, but I'm considering almost exactly what you've done there.)

    Given that you've added the outfeed table to the back Incra rail, how does it handle the...
  4. Replies
    37
    Views
    8,783

    Hey Don, I know this is a super old post, but...

    Hey Don,
    I know this is a super old post, but you are the first I have seen that actually has an Incra on a Sawstop. I have an Incra on my old 90s Delta Contractor saw and I'm thinking of upgrading...
  5. Replies
    24
    Views
    5,812

    Thanks for the advice all. I appreciate it.

    Thanks for the advice all. I appreciate it.
  6. Replies
    24
    Views
    5,812

    Hey all, I have a similar question with regard...

    Hey all,
    I have a similar question with regard to my Delta Contractor saw.

    I know an 8” dado stack will certainly fit on my 10” 1.5 HP Delta Contractor’s Saw (Delta 34-444 early 90s model). But...
  7. Also I wonder if I just bought the single outlet...

    Also I wonder if I just bought the single outlet connector (the piece in between the impeller and the filter units) and just mounted both filters on one filter housing. Same throughput, just the...
  8. Mounting Dust Collector Horizontally??

    Hey all,
    I’ve purchased a used grizzly g0562zp 3hp twin canister filter dust collector and I intend to mate it with a super dust deputy xl. Since it’ll be a two stage unit, do you think there is any...
  9. Since I have to wire my shop up in the first...

    Since I have to wire my shop up in the first place, I'll consider adding 240VAC to the mix. :) Thanks for the input y'all.
  10. Why should I do that?

    Why should I do that?
  11. It really does depend. I have some $$ already...

    It really does depend. I have some $$ already set aside for the Table Saw fence and Router Table. I already have a router and will likely also get my Dad's Band Saw and Drill Press. So it's a...
  12. Setting up a new woodworking shop - have some questions

    Hi all,
    Love the support here. I am not new to DIY stuff, but I am (relatively) new to woodworking. I am about to get to setting up shop and have some questions.

    1. Dust Extraction:
    Working...
  13. Replies
    34
    Views
    16,224

    Hey all, Hate to revive a (2yr) old thread, but...

    Hey all,
    Hate to revive a (2yr) old thread, but it seemed the most relevant to my question. Fairly certain I'm going to build my own router table and add Incra's LS super system to it. As far a...
  14. Combination of BB Plywood and MDF/HPL for Router Table Top

    Hey all,
    I’ve seen a number of arguments against Plywood for a router table top and a number of arguments for an MDF/HPL covered top. Typically, it seems that most folks double up on pieces of 3/4”...
  15. Thanks Glenn. Where'd you get the "L"? Also, do...

    Thanks Glenn. Where'd you get the "L"? Also, do you have an opinion of the Milwaukee vs the Bosch 1617?
  16. Milwaukee 2-1/4 HP Router (5616-xx)

    Hey all,
    I've noticed a lot back in the day (aka 2007-2010) that there were a lot of complaints about the plunge mechanism on the Milwaukee 5616 plunge router. The culprit was apparently a weak...
Results 1 to 16 of 16