Search:

Type: Posts; User: Lee Schierer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.24 seconds.

  1. Replies
    12
    Views
    464

    One other thought. I've noticed on some wood...

    One other thought. I've noticed on some wood that there is tear out on the bottom of the cut that sometimes hangs down and catches on the throat plate, causing you to push slightly harder which then...
  2. Thread: Mice

    by Lee Schierer
    Replies
    12
    Views
    237

    We have the same problem here every fall the...

    We have the same problem here every fall the critters are looking for a warm place to live. The cat can't access the garage, so I use peanut butter on the traps I set. I noticed that the peanut...
  3. Replies
    27
    Views
    1,152

    Did anyone identify the tool between the two...

    Did anyone identify the tool between the two T-bevels? If not can we get a better photo or two of it?
  4. Replies
    27
    Views
    1,152

    You align the spoke in the space between the jaws...

    You align the spoke in the space between the jaws so the wrench is aligned with the spoke. Then you adjust the wing nut to tighten the jaws on the spoke nut. Once it is tight you twirl the wrench...
  5. Replies
    12
    Views
    464

    Check your drive belt tension, it could be the...

    Check your drive belt tension, it could be the belt is slipping when you hit harder sections of the wood.
  6. Replies
    27
    Views
    1,152

    No offense Jim, but you aren't old enough to have...

    No offense Jim, but you aren't old enough to have used one like that.

    Do a search for "antique spoke adjuster" and you will see many examples. My grandfather had one that he used.
  7. Replies
    11
    Views
    380

    We have a timer on ours and it used to help save...

    We have a timer on ours and it used to help save cost because there used to be an off peak rate and special meters that tracked on peak and off peak use. Because we are total electric including all...
  8. Replies
    14
    Views
    609

    Nice looking mailbox. Hopefully the postman will...

    Nice looking mailbox. Hopefully the postman will use it since it an official postmaster approved box.
  9. Replies
    14
    Views
    1,622

    Looking good.

    Looking good.
  10. Replies
    1
    Views
    102

    I don't think there are any standards other than...

    I don't think there are any standards other than normally the thinner drawers are at the top and the deeper drawers are at the bottom. Since it is a kitchen determine what is likely to be placed in...
  11. Replies
    27
    Views
    1,152

    I believe the small tool with the wing nut...

    I believe the small tool with the wing nut located between the Marsh Plane and the saw vise is a spoke adjusting tool for a bicycle or motorcycle.
  12. Replies
    5
    Views
    306

    Interesting design with holes in the doors....

    Interesting design with holes in the doors....
  13. Replies
    14
    Views
    852

    I agree with Mike. However, if you can blow out...

    I agree with Mike. However, if you can blow out the fan end of the motor with compressed air first it would clear any dust of of the switch.
  14. The SMC search function leaves a lot to be...

    The SMC search function leaves a lot to be desired. Open another tab and use google for the same search it will find SMC posts that are relevant.
  15. Thread: Roundover

    by Lee Schierer
    Replies
    7
    Views
    345

    Coincidently, I'm working on a night stand with a...

    Coincidently, I'm working on a night stand with a design similar to the table you showed in your post. I made a little champfer plane that I use to break the corners that I'm not rounding over. The...
  16. Replies
    34
    Views
    1,234

    I'm 71, don't tell anyone...The problem with...

    I'm 71, don't tell anyone...The problem with Craftsman radial arm saws (and most others) is accuracy and repeatablity. The reason you see cuts at angles in the tables is that for cleaner cuts you...
  17. Replies
    7
    Views
    345

    My phone uses Drive pdf viewer or Samsung notes.

    My phone uses Drive pdf viewer or Samsung notes.
  18. Replies
    10
    Views
    495

    Some wood processor formats do not play well with...

    Some wood processor formats do not play well with the Vbulletin software. You may see all sorts of extra weird characters in your text when you post it. Remember you can edit your post for 24 hours.
  19. Replies
    34
    Views
    1,234

    I still have the original motor on mine. About...

    I still have the original motor on mine. About once a year I pull the little plastic caps over the bearings and add a few drops of oil. My motor is 1 Hp and I find it adequate for all the cutting I...
  20. Replies
    34
    Views
    1,234

    I've had my 113 saw for over 30 years and I did...

    I've had my 113 saw for over 30 years and I did the alignment about 5 years after I got it. I checked it a couple of years ago and it had moved maybe 0.002 according to my dial indicator. I rarely...
  21. Replies
    12
    Views
    576

    I'll take one. I need to think about replacing...

    I'll take one. I need to think about replacing the door to my shop from the house. Very nice work.
  22. Replies
    34
    Views
    1,234

    My saw is a 113.298720. I would definitely...

    My saw is a 113.298720. I would definitely recommend changing the pulleys. It has been too many years to recall where I got mine. What you want are machined pulleys of the same diameter and hole...
  23. Replies
    34
    Views
    1,234

    What is the model number of your saw? I have a...

    What is the model number of your saw?
    I have a Craftsman 113 model saw with the cast iron open grate wings. I have tuned my saw, added a Beismeyer fence and a Kreg crosscut guide. I also replaced...
  24. It works great on cars, generally I avoid having...

    It works great on cars, generally I avoid having any amount of silicone near my woodworking. I have personally observed fingerprints on painted surfaces caused by residual silicone remaining on...
  25. Replies
    20
    Views
    714

    When I added additional insulation to our house,...

    When I added additional insulation to our house, I noticed that the added insulation was blocking the air flow from the perforated soffet into the attic. Since the area was almost impossible to get...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4