Search:

Type: Posts; User: steven c newman; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.22 seconds.

  1. Replies
    16
    Views
    1,370

    4 bags of tips should have arrived this afternoon...

    4 bags of tips should have arrived this afternoon at their new home...I hope.
  2. Replies
    1
    Views
    124

    Home for Wayward Spokeshaves

    Since I still had some left over scraps of Ash....maybe a Frame &Panel style of lidded box...Panels are 1/4"-3/8" thick resawn Ash...frames are 3/4" x 3/4" 'sticks"....Also, a bit of Tongue & Groove...
  3. Looks very good....when's the test drive?

    Looks very good....when's the test drive?
  4. even did a 3rd coat of clear gloss poly...then...

    even did a 3rd coat of clear gloss poly...then decided to add a "brand" to the box...
    461596
    yes, I do have a branding iron...BANDIT'S Dungeon WOOD SHOP...
    Think I can call this little box...
  5. Waiting on coat #2 of clear gloss to dry, and get...

    Waiting on coat #2 of clear gloss to dry, and get a rub down...PIP?
    461547
    Oh, BTW....added a chain to the lid...
    461548
    Need to hit a couple spots I missed?

    Stay tuned..almost done...may...
  6. Replies
    16
    Views
    1,370

    Tips will be going to their new home..may need a...

    Tips will be going to their new home..may need a few "Extras" to pad out the box...we'll see


    Stanley Eggbeater drill: Needed a good oiling up...runs nice and quiet now.....drill bit either...
  7. 1st coat of Clear Gloss Poly has been...

    1st coat of Clear Gloss Poly has been applied....waiting on that to dry...
  8. Replies
    16
    Views
    1,370

    Since I do not really need any of those bits, and...

    Since I do not really need any of those bits, and nobody wants these...they will get tossed out

    Along that $3 line of thought...that is what I spent, yesterday...
    461449
    $2 Eggbeater drill...
  9. Replies
    73
    Views
    3,092

    "If a hammer won't work.....get a bigger one.."

    "If a hammer won't work.....get a bigger one.."
  10. Well...needed some sort of "rack" hold them...

    Well...needed some sort of "rack" hold them still. Didn't want to use Ash to hold Iron tools, so, some Pine scrap was used....Cut into 2 pieces...one needed a trim off the top..
    461441
    Notched...
  11. 2nd coat is brushed on...need to do a bit of...

    2nd coat is brushed on...need to do a bit of "Design Work"..
    461368
    To make a rack of some sort to hold these 4 'shaves.....and keep them in place.....

    Not enough room in here, to include the...
  12. Let's see.. 461296 Top rail through mortise...

    Let's see..
    461296
    Top rail through mortise
    461297
    Lay out marks..
    461299
    Lock rail mortises...
    461300
    Lock Rail...pins and wedges
  13. Ok...been a long time since I have done...

    Ok...been a long time since I have done doors....last ones were passage doors...and a couple screen doors..

    I used through mortises....with both pins and wedges. The panels were raised, but they...
  14. Replies
    16
    Views
    1,370

    None would fit...so....I can either toss them...

    None would fit...so....I can either toss them out, or send them to someone who does have handles that would work....I do not.
    461278
    Nutdrivers, all SAE sizes....have already tossed the 3 worst...
  15. OK...got the rest of the rounding overs...

    OK...got the rest of the rounding overs done..ends..
    461268
    And the front and back of the lid..
    461269
    Lay out for the hinges...and the fighting....laid out on the lid, first..
    461270
    Along...
  16. Afraid I don't do any carving... Had to clear...

    Afraid I don't do any carving...

    Had to clear the top of the bench, today...
    461227
    Was getting a bit ...crowded....One router to do some round-overs...the other (DeWalt 610) had an edge...
  17. Replies
    16
    Views
    1,370

    Got to looking around...seems I have seen that...

    Got to looking around...seems I have seen that Ratchetool...before...
    461189
    Open..
    461190
    Hmmm, open..
    461191
    Seems I now have quite a few handles, to choose from....Orange handle has it's own...
  18. Replies
    73
    Views
    3,092

    Can judge a good Carpenter by how small his pile...

    Can judge a good Carpenter by how small his pile of scraps are.

    They used to say I was too slow....until I pointed out..I only need to do a task ONCE. Most times, the super fast ones? They...
  19. Replies
    16
    Views
    1,370

    Carpenter's Scribe.. 461123 All cleaned up, can...

    Carpenter's Scribe..
    461123
    All cleaned up, can even read the GENERAL logo...backside?
    461124
    Even gave it a new pencil...

    Chisel...
    461125
    Cleaned the handle up, and can just make out the...
  20. had Laundry Detail, today....means I was also...

    had Laundry Detail, today....means I was also down by the shop.....decided to at least remove the clamps, and see how close the lid fits the box....hmmmm, needs a bit of trimming...how to hold it...
  21. Replies
    7
    Views
    900

    Well, THIS No. 9-1/2 has been getting used.....

    Well, THIS No. 9-1/2 has been getting used..
    461042
    Along with the Big Boys...
    461043

    A little Ash end grain.....
  22. Clamps removed....plywood for the bottom of the...

    Clamps removed....plywood for the bottom of the box was cut to size.
    .460993
    On the bandsaw, no less.....was able to follow a straight line...even splitting the lines...very little, if any, clean...
  23. Going over the photos now....Lid is in the...

    Going over the photos now....Lid is in the clamps....box now has a bottom...Back is quite sore, right between the shoulder blades.....must have been all those way too thin shavings....
    460977...
  24. Maybe after Lunch today...I can meander down to...

    Maybe after Lunch today...I can meander down to the shop....we'll see...

    Stay tuned
  25. Replies
    10
    Views
    990

    460969 About the same way I fixed this......

    460969
    About the same way I fixed this...
    460970
    Tenon vs groove..one was tilting a bit...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4