Thanks for the help
I think I know the issue that is causing the twist.
I try the sanding or plane method to flatten the bottom.
Larry
Type: Posts; User: Larry Cronin; Keyword(s):
Thanks for the help
I think I know the issue that is causing the twist.
I try the sanding or plane method to flatten the bottom.
Larry
I realize I did a terrible job of asking my question.
What I was looking for is some help in approaching the situation.
Do I start by sanding the part of the crib that touch till I get all...
I should have better described it. That piece in the photo goes on a base that has rockers attached to it.
So it would need to be flat on the bottom to connect to the base.
Larry
Hello
I made a couple doll cribs and I did something wrong and they are not "flat". I am hoping that someone out there can give me some guidance on how to solve the issue. I am nervous that if I...
Thanks for replies.
I missed that sale. In my next life I am going to pay more attention.
Larry
Hello,
Anyone have any experience with these Bessy Clutch Clamps? GSCC2.506 and GSCC2.512. They are at HD for $25 for a 4 pack, 2 6 inch and 2 12 inch.
Seems very affordable for my type of...
So I messed arounf a bit and tried a few different things suggested here.
THe one thing I did not try yet was to champfer the holes. I dont have a champfer that big and my champfer bit for my...
Thanks for all the suggestions.
I will try a bigger hammer and also I am going to try and rough up my holes and see if that helps.
I will report back in a day or so.
Larry C
Hello,
I built my workbench with lots of advice and knowledge from here.
Came out really good and works great.
But
I cant get my holdfasts to work at all.
Just to wrap it up.
I had a some trouble locating both the 7 inch and 8 inch outside vents that were readily available.
So I am going with the 7inch to 6inch reducer and see how it works.
...
Thanks for the suggestions.
I am going to look around a bit today and see if I can find some 7 inch stuff.
If I can and it looks like it may work I might go with that. If it involves ordering...
Hello,
I have a Laguna 2HP manual clean dust collector (MDC0560-0145) that I am going to vent outside. Who knew besides those that read the manual or measured the outlet pipe that it is 7 inches....
I was thinking of doing my glue up in the one board at a time method. I work from home and could get a few boards done in a day.
I am still in the hunt for a No 7 plane.
Thanks again to all of...
I was not clear my no 9 is a Stanley 9 1/2 block plane.
I am looking at adding a 7, started the search for a used one initially.
I do have a few hand planes which I am trying to use more and more. I own a No. 9, No 4, and a No 62.
Thanks very to all of you for the suggestions and encouragement.
If all goes well I will...
Thank you all for the suggestions and encouragement.
I have to get started before I convince myself that I should wait and look at buying again.
Larry Cronin
Hello,
I am thinking of building a workbench, I cant bring myself to buying one.
The size would be roughly be 26" by 65". Bigger will not fit in my shop.
I plan to make it out of hard...
Sorry I got side tracked with Thanksgiving.
Thanks for the suggestions and to Dom Greco, thanks for one of the best write ups I have ever seen. Photos, links, and a wiring diagram.
At my house...
When I looked at the iVac I was adding in the cost of also buying the auto switch for each of my tools. So at $80 plus $60 a tool it was costly.
I think I am leaning towards the PSI one you...
That looks pretty cool but it may be more than I want to spend.
Hello,
Has anyone found an aftermarket replacement for the Laguna remote control. Mine died and I was hoping to get something a little more robust.
Should I just go and get a remote switch...
Hello,
I just wanted to follow up and let the thread know what I did. I ended up having a local sheet metal shop make them for me. They were $6 a piece using 1/4" stainless rod. I just never ...
Per your suggestion I am planning on going to a metal supply place this week.
Thank you to all for the replies. It has been very helpful.
I will let you know how I make out.
Larry C
Thank you for all the suggestions. I may purchase some 1/4 steel rod and see if I can figure out how to bend it with some consistency and relative ease. I have a stupid question, is cold roll steel...
Charley,
I think I just may pay someone to make these, or come up with another way to do it?
I think I am heading down a rat hole here and unlike wood, I will not be able to use my mistakes in...