Search:

Type: Posts; User: Tom Bender; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. testing post

    testing post
  2. Replies
    9
    Views
    362

    Yeah my Teco is silent. A couple of cautions...

    Yeah my Teco is silent.

    A couple of cautions with VFDs;

    You only get so much speed reduction, maybe 30% so a 3600 rpm motor only runs at 1100 rpm and above.

    A VFD can run your motor at...
  3. Replies
    3
    Views
    352

    Can you tilt the arbor?

    Can you tilt the arbor?
  4. Maybe just ignore it.

    Maybe just ignore it.
  5. Replies
    20
    Views
    1,064

    I had the excellent job of managing construction...

    I had the excellent job of managing construction for a major manufacturer. We always used union trades. They were expensive but we almost never had quality issues. Each and every worker carried pride...
  6. Replies
    33
    Views
    3,706

    In New England we had 15 amp 240 volt services....

    In New England we had 15 amp 240 volt services. You get 4 - 15 amp 120 volt circuits out of it and of course that adds up to more than the service is supposed to provide. I think the theory was that...
  7. Replies
    13
    Views
    815

    I put up a lightweight shelter for my brother...

    I put up a lightweight shelter for my brother last year in a sheltered spot. Big wind shredded it a month later.

    Firewood is fine out in the weather, just sweep the snow off it and bring it in.
  8. Replies
    15
    Views
    864

    Home Defense works ok.

    Home Defense works ok.
  9. Replies
    12
    Views
    1,141

    General Metalworking I have a piece of heavy rail about 6" long. It...

    I have a piece of heavy rail about 6" long. It was part of the debris from a switch that had been demolished. I don't know how a 6" piece figured into a switch. It has smooth flat ends. The top is...
  10. Replies
    3
    Views
    451

    Some lessons are painful. If it only took 6...

    Some lessons are painful.

    If it only took 6 weeks to make the first time, it should only take 3 weeks to make again.
  11. That would go in my "Scrap Solvent" can. It's a 1...

    That would go in my "Scrap Solvent" can. It's a 1 quart paint can (properly labeled). It gets half full in about half a year, (I'm parsimonious with solvent), then it gets burned in the fire pit,...
  12. Replies
    3
    Views
    525

    Got my steps in today

    The task for today was to raise the outside hose bib a couple of feet. This involved moving it a few feet to the east so it would go into a closet wall, so the freeze proof faucet didn't come thru...
  13. Replies
    25
    Views
    1,424

    No, just a pliable head, a cup of tea in the...

    No, just a pliable head, a cup of tea in the morning gets to me in the wee hours.
  14. Replies
    25
    Views
    1,424

    Caffeine - Rollercoaster into Hell

    Caffeine and other stimulants I have tried provide a nice boost but it's a rollercoaster that goes a little less high and decends a little lower with each cycle.
  15. Replies
    2
    Views
    266

    Skeleton Keys

    I have about 30 old Skeleton Keys and would like to use them as decoration in some way.

    The finish varies from shiny to rusty so naked or painted are options.

    Any suggestions?
  16. Replies
    11
    Views
    747

    If you experience an explosion in a cardboard or...

    If you experience an explosion in a cardboard or plastic tent you will get singed and knocked on your butt, but your house will remain standing.
  17. Replies
    5
    Views
    483

    The small ones will make nice cutting boards with...

    The small ones will make nice cutting boards with very little work. Round over and add rubber feet.

    Cut the large ones into smaller squares and assemble them into parquet panels for wainscoting...
  18. Replies
    1
    Views
    247

    You're gonna need some wooden parts too.

    You're gonna need some wooden parts too.
  19. Replies
    7
    Views
    687

    Agree with Mike. Though I glue in plywood...

    Agree with Mike. Though I glue in plywood bottoms, slips will work just as well.
  20. Replies
    13
    Views
    878

    If a giant dovetail is not in the cards you can...

    If a giant dovetail is not in the cards you can use a dado for alignment and screws to hold it in place. To accommodate expansion there are two good approaches that come to mind.

    1. Oversized...
  21. Replies
    33
    Views
    2,916

    Tom Bussey, that's a slick solution.

    Tom Bussey, that's a slick solution.
  22. Replies
    13
    Views
    979

    Nice bench but it looks like it could have a...

    Nice bench but it looks like it could have a couple of issues.

    The top may shrink and warp as it dries. Not a biggie but will be noticeable. And with it restrained by the crossmember, something...
  23. Replies
    7
    Views
    542

    Start with a 45 cut on the table saw then go to...

    Start with a 45 cut on the table saw then go to the hand planes.
  24. Replies
    11
    Views
    934

    Do you have your feed arrow pointing the wrong...

    Do you have your feed arrow pointing the wrong way?
  25. I like the tuning fork tool but have an...

    I like the tuning fork tool but have an improvement to suggest. Say the hole is 3/4", make the tool with 3/4" x 1/8" flat metal. File or grind a little as needed to fit into the hole. Bend it into a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4