Search:

Type: Posts; User: Jim Andrew; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds; generated 25 minute(s) ago.

  1. Replies
    34
    Views
    5,193

    I replaced all my bulbs several years ago, found...

    I replaced all my bulbs several years ago, found some on ebay that cost half of the ones at Menards. Took out all the ballasts, and the extra wire, mine are hot on one end only, and they are much...
  2. Replies
    21
    Views
    8,760

    Be sure you understand the zoning rules in your...

    Be sure you understand the zoning rules in your area. Years ago when I was in the building business, tried to build a house with oversize garage planning to build the cabinets for the homes I built....
  3. Replies
    12
    Views
    6,723

    The pragmatic luthier on Youtube is interesting...

    The pragmatic luthier on Youtube is interesting to watch.
  4. Replies
    10
    Views
    12,701

    What I have been reading is you make a guitar...

    What I have been reading is you make a guitar neck from a 1" thick piece. Have a 12" rip blade for the Hammer saw, was trying to figure out a way to use the sliding table to make the cut, thinking a...
  5. Replies
    10
    Views
    12,701

    How to mark and cut a 10 degree angle

    Have both a MM 16 and a Hammer sliding table saw, and was thinking of the most accurate way to cut a 10 degree angle. Was talking to a retired machinist friend, he said he has some type of...
  6. Replies
    14
    Views
    2,807

    Decided to measure the radio cord, has a flat...

    Decided to measure the radio cord, has a flat cord 4x7 mm. Will a 7 mm ferrite ring work?
  7. Replies
    14
    Views
    2,807

    Thanks, guess I will try what Lee suggests.

    Thanks, guess I will try what Lee suggests.
  8. Replies
    14
    Views
    2,807

    static on my radio

    I get static on my radio, it is a Sony boombox type, and FM is the problem. It is fine until I turn on the lights. The lights are all LED in the drop in type fluorescent fixtures, when they were...
  9. Did you get the belt over the Y where the air...

    Did you get the belt over the Y where the air fittings attach? One of the first times I used my Grizzly 15" sander, I got the belt over the Y instead of behind it, and ground off one of the air...
  10. Replies
    69
    Views
    14,187

    Glad I already have a pretty good shop setup. ...

    Glad I already have a pretty good shop setup. Would not be wanting to buy much at these prices. The official inflation rate is about 7%, but have heard financial people saying that the real...
  11. I have the 15" Grizzly 5hp, and have no problems...

    I have the 15" Grizzly 5hp, and have no problems with it making flat panels. I do not usually go over 24" panels, and the open end sands those panels flat. Really glad I bought a new open end...
  12. Replies
    0
    Views
    683

    Metabo hpt C12rsh2 and Kreg fence?

    Found a good deal at Menards to replace my 15 y/o Makita sliding miter saw with a Metabo hpt 12" sliding miter saw. The Makita had a little peg on the fence so you could move a fence part away for...
  13. Replies
    7
    Views
    852

    Thanks for the replies.

    Thanks for the replies.
  14. Replies
    7
    Views
    852

    18v Dewalt drills, and batteries.

    I have several 18v Dewalt drills, was cheaper to buy another drill than a pair of batteries, and now I am down to about 6 batteries. Was wondering if anyone has bought any of the non-dewalt...
  15. Replies
    10
    Views
    882

    Before you take the planer apart make sure there...

    Before you take the planer apart make sure there is no reset button. If you have an owners manual, read that part. My Grizzly 15" will overheat if you try to run a load of lumber through it, and...
  16. Replies
    10
    Views
    1,608

    Have a neighbors who is a commodities broker, he...

    Have a neighbors who is a commodities broker, he said people were really getting slammed who bought lumber on the board. No buyers to sell to. He said each contract was costing them 6,000 per day,...
  17. Replies
    24
    Views
    2,977

    Mice can cause problems with your wiring. Think...

    Mice can cause problems with your wiring. Think I would wire, insulate, then cover the walls with either wall board or wafer board.
  18. Replies
    21
    Views
    2,393

    If you happen to take a trip to Jamaica, try the...

    If you happen to take a trip to Jamaica, try the variety grown there, if I recall correctly it is Blue Mountain coffee. They make it strong. If you just drink coffee there, it will be Folgers, they...
  19. Replies
    15
    Views
    2,879

    I bought inexpensive LED bulbs, and rewired all...

    I bought inexpensive LED bulbs, and rewired all my 4' fluorescent fixtures for LED. Happy, and the light is much better.
  20. Replies
    26
    Views
    6,439

    I put down 1" thick treated YP 4" deck flooring...

    I put down 1" thick treated YP 4" deck flooring on 16" centers, cut 1" blue dow foam to fill in the gaps, then laid t&g flooring over the top. All splices are on the sleepers. Mine is not finished...
  21. Replies
    39
    Views
    8,488

    You can buy an outside woodburning furnace. I...

    You can buy an outside woodburning furnace. I built a small steel building, and installed a wood furnace, then ran ducts for supply and return to the shop, as I did not want to have a fire in my...
  22. Replies
    41
    Views
    8,139

    Think if you check, the Grizzly and the CV both...

    Think if you check, the Grizzly and the CV both have larger impellers than the Oneida. Larger diameter impeller means more suction. Would go with the CV 16" if you go CV. 5hp will handle the...
  23. Replies
    11
    Views
    4,338

    Last I knew Penn state industries was still...

    Last I knew Penn state industries was still selling a 2hp blower assembly.
  24. Replies
    7
    Views
    1,041

    I used to have a terrible time with glued up...

    I used to have a terrible time with glued up panels till I built a solar wood drier. Now I have a ready supply of dry wood.
  25. Replies
    19
    Views
    3,738

    When I worked at the cabinet shop, we ran a 1/4 x...

    When I worked at the cabinet shop, we ran a 1/4 x 1/4 groove on the face frame, then machined the side panels so they had a 1/4 x 1/4 tongue, then put glue in the groove, slid the side panels in and...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4