Search:

Hey folks

I am trying to find info about belt tension for Delta Unisaw. I type in unisaw belt tension, tablesaw belt tension, unisaw belt adjustment and there are no matches. How is that...

Hey Jerry, thanks for replying.

I could see no way of easily adjusting the location of the arbor pulley, and so I have already put the top back on. And definitely began to worry when I saw your...

Update:

So I installed the pulley and tried to line it up with the arbour pulley. In doing so I have to move the motor pulley to be 3/16th off the motor shaft, about a 1/4 away from the motor. I...

Update: So I removed the top and found what y'all suspected to be the case. However, not only did I find just a single hex fastener in each pulley thread/slot, but that the fasteners were at...

Hey Folks, thanks for all the responses. I did try taking the face plate off to blow out the switch, prior to the duct tape band-aid, but to no effect. Although dust is likely the cause, as I had...

Hi All

So my Delta Unisaw X5 has stopped working. The motor sounds as if it is running (albeit not healthy sounding), but the belt and blade do not spin. It began when the on/off switch stopped...

I assumed there wouldn't be any easier answers - Thanks Anyhow!

Hey All - So I am applying the General HP over dewawed shellac and am getting mixed results. The work piece is a 9'x2' bench (Nakashima Conoid Bench), and I am applying with a painters pad, or...

Bigafence - that may be the way to go. Nice one, Thanks for the replys.

Looks like a good solution - but I am in Ontario and cross border shipping may not be worth it.

Hey All - I assume most have upgraded from your Unifence systems, and thats why I couldn't find the pertinent info I was searching for, hence the new thread.
My situation is that I have the Unisaw...

Considering making an interior door for a bathroom,335789 I don't know if the construction would change because it would be subject to more humidity. But I was hoping someone on here might have an...

So I am making a Nakashima Conoid bench, 335430, the bench is 9ftx2ft wide, and the back support has already been glued and assembled. The slab has twists and cups, and so I had to make each leg a...

Movement around the legs, in what direction? Is that what split in the middle would offset? And how would that look? Like a Nakashima butterfly joint or something? Is there a risk of the board...

Hey there, so as the title suggests I'm considering putting a wooden vanity with a top and bottom shelf in my bathroom renovation. 330916 I have concerns that the 2'' slab that I intend to use as the...

It's my first big project. Live and learn. But a water based dye sounds like my best bet. Thanks for the help.
In regards to securing the bark, what about Tung Oil? Nakashima's live edge bench's...

So I applied some General's HP Topcoat to the bark of a live edge bench,(9ft long) and the coating is almost invisible. I was going for a darker, thicker covering(just on the bark, not the Maple...

That is unfortunate. Could I put a paint thinner, or something else you could recommend on the bark to remove the poly and try again with something else? I like the look of the darkened bark with the...

I did search but couldn't find this exact question - but I was wondering if I can cover a coat of General's Water Based High Performance Top Coat with a Minwax Helsman Spar Urethane. I would only be...

So I am making a bench from a large slab that has warped slightly, and while the leg will still enter perpendicular to the ground, the shoulder that meets the slab's under surface will not meet flush...

Hey Guys - working on a Nakashima Conoid bench, its my first major project and I am hoping to have it ready by Christmas. Here's a pic so were on the same page.327421327422
I am planning on...

The slab is two inches thick and has a good percentage of non spalted which runs the length of the board, and will hopefully support the weaker areas, there has been no cause for concern up to this...

Hey folks, as the title suggest I am finishing a bench which has undergone a spalt and this spalted area is close to half the surface area. Any ideas for a finish does not make the spalt look dull...

I have a large slab of spalted maple that I planed about 6 months ago, meant for a live edge bench with a spindle support backrest, and a work in progress ever since. The slab is about 21'' wide and...

Also what amount of splay am I looking to achieve? If the tenon is 1&3/16, what would the be the new dimension with a wedge, and also the ideal wedge size. And how should I taper the mortise, ie....