Search:

Type: Posts; User: David Buchhauser; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. I agree with Peter and Lisa! That is a toggle...

    I agree with Peter and Lisa! That is a toggle clamp that mounts to the T-slot on the top of the fence shown in the second picture.
    David
  2. Replies
    6
    Views
    175

    Unless one of your other belts was defective or...

    Unless one of your other belts was defective or grossly out of balance, I doubt that was your problem. Does the motor have rubber mounts or is it rigidly mounted to the mounting plate? I'm guessing...
  3. Replies
    17
    Views
    639

    AutoDesk does have a RichAuto post processor...

    AutoDesk does have a RichAuto post processor available for Fusion 360 which has apparently been tested by some of the Axiom owners who have reported back that it does work fine. This is the RS274...
  4. Replies
    17
    Views
    639

    Just a note: When using Fusion 360 - Design and...

    Just a note: When using Fusion 360 - Design and Toolpaths are also done in the same software. Fusion 360 does the design, the CAM (toolpaths/simulation), and the post processing - creating gcode...
  5. Replies
    17
    Views
    639

    I agree that the learning curve for Fusion 360 is...

    I agree that the learning curve for Fusion 360 is a little steeper than that for VCPro - but it's really not all that bad. For a guy on a tight budget with more time than money, then Fusion 360 may...
  6. Thanks Bob!

    Thanks Bob!
  7. The "shoe" is shop made. I machined the runners...

    The "shoe" is shop made. I machined the runners to for a good fit into the slider slots. The miter bar on the Incra is adjustable for a snug fit into the table saw miter slots.
  8. Incra miter sled with right half installed. Table...

    Incra miter sled with right half installed. Table saw dust collection.

    419230419231
  9. Hi Terence, I like it! I have basically the...

    Hi Terence,
    I like it!
    I have basically the same slider attachment on my table saw. I have the Incra miter sled mounted so that it is attached to the slider, but the miter bar rides in the table...
  10. For Sale: Incra LS25SYS 25" Range Positioner,Pro-II Joinery Fence System, New - $295

    Incra LS25SYS 25" Range Positioner with Pro-II Joinery Fence System - New In Box. $295.00 plus shipping.

    I purchased this brand new in April 2019 - was going to use it for a table saw jig but...
  11. Hi Keith, I purchased my 44' x 60" digitizing...

    Hi Keith,

    I purchased my 44' x 60" digitizing tablet here:
    https://www.ebay.com/itm/CNC-Plasma-Tracer-and-Pen-44x60-Digitizing-Tablet/311614679875?hash=item488daeab43:g:1KsAAOSwubRXOI2I

    I...
  12. Hi Keith, I initially misunderstood Stan's...

    Hi Keith,
    I initially misunderstood Stan's process (my fault). I was originally thinking that he had taken a photo of the sign with the heron and was just wondering what his method was to convert it...
  13. Replies
    13
    Views
    486

    Hi Ronald, I think you would be better off to...

    Hi Ronald,

    I think you would be better off to get a second desktop pc instead of the laptop (might be cheaper for a decent used/reconditioned one). Then install a second seat of VCarve Pro onto...
  14. I purchased a shop vac exhaust "muffler" on...

    I purchased a shop vac exhaust "muffler" on Amazon to try out with my large Craftsman shop vac. It didn't really make it any quieter that I could tell, but it did restrict the exhaust flow and seemed...
  15. Will, I have drilled lots of holes (into...

    Will,
    I have drilled lots of holes (into plywood) using my cnc router table. It has a variable speed spindle with a range from 8000 to 24000 rpm. The main thing is that I am limited to drill bits or...
  16. OK. I think I understand. You had a jpg image of...

    OK. I think I understand. You had a jpg image of the heron and the print shop printed the heron onto paper and you used this to lay over your digitizing board to trace it.
    I have a program intended...
  17. Did you take a picture of the page in the...

    Did you take a picture of the page in the coloring book and have it printed to a larger size? If so where did you take it to have it printed to the larger size?
    Or is the page you are tracing in...
  18. Hi Stan, How did you convert your photograph of...

    Hi Stan,
    How did you convert your photograph of the bird to the paper pattern drawing that you used to trace onto the digitizing board?
    David
  19. But Johnny, Here it is. There is apparently a...

    But Johnny,
    Here it is. There is apparently a market for these cutters, or they probably wouldn't make them. I didn't even know that these were available.
    David
    ...
  20. Hi Steve, I own two of the Grizzly G0640x type...

    Hi Steve,
    I own two of the Grizzly G0640x type vertical band saws and I think they are great! I originally purchased these because of that metal/wood speed feature. I currently have one set up for...
  21. Replies
    13
    Views
    549

    Once again Andy, I must disagree! I have run the...

    Once again Andy, I must disagree! I have run the dado stack on both of my table saws many times with no problems. As others have mentioned, when running at full width both washers don't fit. This is...
  22. Replies
    16
    Views
    1,011

    Hi Steve, I like the way you think! I feel the...

    Hi Steve,
    I like the way you think! I feel the same way about changing blades. Same with sanding belts, Mig welder wire size, grinder flap discs, etc. So I have multiples of many of these tools. I...
  23. Andy, I'm afraid that I will have to disagree...

    Andy,
    I'm afraid that I will have to disagree with you. I've still got most all of the "small machines" that I started out with over 35 years ago. I have since acquired many larger and more capable...
  24. Replies
    19
    Views
    1,235

    Supposed to be funny - but I don't get it. What...

    Supposed to be funny - but I don't get it. What is "olic"
    David
  25. Hi John, You are probably right - the Avids are...

    Hi John,
    You are probably right - the Avids are great machines. I have one setup for wood, and the other will be put into service dedicated to high speed aluminum machining. But I also have a...
Results 1 to 25 of 436
Page 1 of 18 1 2 3 4