Search:

Type: Posts; User: Jim OConnor; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    918

    Hi Rod, I have the same question. Could you...

    Hi Rod, I have the same question. Could you please PM me as well with the info? Thank you
  2. Replies
    20
    Views
    3,182

    The infinity tools set up jig works really well....

    The infinity tools set up jig works really well. I could never set up this joint until I got this jig. I have set up blocks, but, as someone else said, it was pretty challenging to set up. I did...
  3. Replies
    13
    Views
    2,156

    SCM & Felder offer really good machines across a...

    SCM & Felder offer really good machines across a wide spectrum of prices. From that perspective, it comes down to preference. The most significant difference I found is the higher end Felder’s can...
  4. Make sure you disengage the planer rollers when...

    Make sure you disengage the planer rollers when you’re done using it. This will help prolong the life of the roller drive
  5. Replies
    12
    Views
    1,897

    Think about how much weight this adds to the...

    Think about how much weight this adds to the elevator. I’d think you would want to be a little careful about “permanently” reducing the passenger capacity……
  6. So where do you get the bags for your UDD?

    So where do you get the bags for your UDD?
  7. Replies
    14
    Views
    1,844

    Splitting permanently or temporarily? Radically...

    Splitting permanently or temporarily? Radically different questions….
  8. Replies
    29
    Views
    3,432

    If you come across one, an OMGA radial arm saw is...

    If you come across one, an OMGA radial arm saw is also a really solid industrial saw
  9. Replies
    14
    Views
    2,786

    Very nice!

    Very nice!
  10. Jim rather than cutting the long fence, if you...

    Jim
    rather than cutting the long fence, if you are primarily using the fence as a bump stop, have you considered making a short L Fence that would mount to the base in lieu of the factory fence? ...
  11. Jump over to the Felder Owners Group and ask. ...

    Jump over to the Felder Owners Group and ask. Someone will know where that safety switch is.
  12. Replies
    15
    Views
    2,212

    Thanks Mark!

    Thanks Mark!
  13. Replies
    15
    Views
    2,212

    Mark, can you post a couple of pictures of your...

    Mark,
    can you post a couple of pictures of your set up? I also have Norfab pipe and have been thinking about going to an overhead design on my slider. There are a variety of things I don’t like...
  14. Replies
    123
    Views
    18,657

    Suggest you join the Felder Owners Group. Lots...

    Suggest you join the Felder Owners Group. Lots of people familiar with Felder engineering. I suspect someone has been down this path before and can help.
  15. Replies
    6
    Views
    1,660

    2-3 thousandths above the cast iron. You do not...

    2-3 thousandths above the cast iron. You do not want the wood dragging on the cast iron.
  16. Looks like a good prize. Please count me in.

    Looks like a good prize. Please count me in.
  17. I second the block plane. This should be easy...

    I second the block plane. This should be easy for a sharp good quality block plane. Make sure you draw pencil lines on the top and side edges then plane to the lines.
  18. Slip it Gel works nicely and lasts a long time. ...

    Slip it Gel works nicely and lasts a long time. Very easy to apply
  19. Use a leaf blower from the outside…..if it’s...

    Use a leaf blower from the outside…..if it’s really clogged, you may have to blow out the inside as well. Avoid high pressure “spot” cleaning with an air hose close to the filter.
  20. Check all the gasketed connections. Gaskets May...

    Check all the gasketed connections. Gaskets May be deformed and or connection may have loosened. Mine had a slight leak on top of the filter due to a deformed gasket. Replaced the gasket and the...
  21. Replies
    22
    Views
    2,764

    Jadawley.com industrial mitre saw stations. ...

    Jadawley.com
    industrial mitre saw stations. Excellent fences with no flex and easy repeatability. Not inexpensive, but industrial equipment never is.
  22. Replies
    23
    Views
    2,402

    Prefer the X style since they don’t slip down my...

    Prefer the X style since they don’t slip down my shoulder. Be careful of the metal hammer loops or tape measure holders…. They can drag across cabinets and tools and scratch all your hard work.
  23. Replies
    38
    Views
    3,924

    Should be the same width as the body. If yours...

    Should be the same width as the body. If yours is narrow, you may have to bias it to one side to see if you can get it to the edge……. But 1/16” is a big gap
  24. Replies
    7
    Views
    5,466

    Thank You. Order has been placed with raised...

    Thank You. Order has been placed with raised gantry, spindle, and several other bells and whistles!
  25. Replies
    7
    Views
    5,466

    Stinger 1 Gantry Lift

    Getting ready to order a CAMaster Stinger 1. Should I get the 2” gantry lift option?
Results 1 to 25 of 36
Page 1 of 2 1 2