Search:

Type: Posts; User: Cliff Polubinsky; Keyword(s):

Page 1 of 14 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    30
    Views
    1,285

    Jason, Don't know where in Western Ohio you...

    Jason,

    Don't know where in Western Ohio you are but I've been happy with Seifker Sawmill near Elida, just a little west of Findlay. They'll let you pick through the stacks and help you pull what...
  2. Replies
    12
    Views
    553

    Alan, I used the overarm dust collection for...

    Alan,

    I used the overarm dust collection for years. As soon as I saw the overhead guard I bought it. What I found was that it didn't do much better than the overarm guard with dust. Maybe I had...
  3. Replies
    60
    Views
    3,550

    Derek, Everclear is 190 proof (95%) grain...

    Derek,

    Everclear is 190 proof (95%) grain alcohol and is drinkable. You can get or order it at your local liquor store.

    Cliff
  4. Millers Falls Langdon Acme 74 miter box - Fort Wayne, IN

    Millers Falls Langdon Acme 74 Miter Box with Disston saw. Everything is fully functioning and the saw has been recently sharpened by Bob Page at Loon Lake Toolworks. If I'm reading the dating sites...
  5. Orren, Rockler has these...

    Orren,

    Rockler has these that fit Bessey handles. I have them on all my K bodys and they make a big difference.

    Cliff
  6. Phil, An excellent school to look into is the...

    Phil,
    An excellent school to look into is the Marc Adams School in Franklin Indiana. It's 12 miles south of Indianapolis so would be a little under 5 hour drive from Detroit. Marc brings in the best...
  7. Replies
    17
    Views
    1,073

    Monte, I saw a photo of Derek Cohen's shop...

    Monte,

    I saw a photo of Derek Cohen's shop that hit me with a 'why didn't I think of that' moment. Cut the bottom of the bottom bag off and clamp a short barrel like the Oneida 17 gallon. Then...
  8. Replies
    16
    Views
    1,332

    Charles, I have the Benchcrafted wagon and leg...

    Charles,

    I have the Benchcrafted wagon and leg vises on my split top roubo. Absolutely no complaints about either. I probably use the wagon vise 10 to 1 over the leg vise.

    Cliff
  9. Replies
    13
    Views
    737

    Lee, in the test I did I put glue on both sides...

    Lee, in the test I did I put glue on both sides of the miter and after curing I couldn't pull it apart by hand nor break it apart with clamps.

    Cliff
  10. Replies
    13
    Views
    737

    I had to try it for myself

    I've seen people clamp a mitered box with painters tape. And I've read that if you're using plywood you can glue miters with no additional reinforcement. I've been slightly sceptical about both...
  11. I use the Fein vacuum with Festool sanders and...

    I use the Fein vacuum with Festool sanders and the Domino. Get the Dust Right FlexiPort Power Tool Hose Kit add it to the end of the Fein hose. You can screw it directly to the Fein hose without any...
  12. Heck, if I only bought the tools I really needed...

    Heck, if I only bought the tools I really needed I'd have a third less tools and half as much fun.

    Cliff
  13. Replies
    133
    Views
    30,382

    Sticky: I would like to register. Thanks Cliff

    I would like to register.

    Thanks
    Cliff
  14. The crosscut table is installed and dialed in....

    The crosscut table is installed and dialed in. The first time through I did the 5 cut test with a 8" square. 90 degree cuts seemed dead on but 45s were off a little. Tried a number of things but...
  15. Thanks for all feedback. I went ahead and picked...

    Thanks for all feedback. I went ahead and picked up the Sliding Crosscut table yesterday.

    While the store was checking that their stock was the new version I was talking to one of the Sawstop...
  16. Anyone using the Sawstop sliding table?

    Every time I go to the woodworking store I have to look at the Sawstop sliding table. It just seems to call to me. But I keep reading the complaints that there are no detents and how can you be sure...
  17. Replies
    35
    Views
    3,407

    I've had good luck with the ION Tough Sounds...

    I've had good luck with the ION Tough Sounds headphones.

    Cliff
  18. Replies
    7
    Views
    873

    I put my A3 31 on the Shopfox heavy duty mobile...

    I put my A3 31 on the Shopfox heavy duty mobile base. Picked up an extra pair of the swivel wheels from Amazon so I have 4 rotating wheels. Had to drill new holes in the non-swivel wheel platforms so...
  19. Joe, Don't know what kind of problem they are...

    Joe,

    Don't know what kind of problem they are referring to. I have that set up and it works fine. Just run a hose from one to the other.

    Cliff
  20. Replies
    3
    Views
    481

    Vacuum veneering question

    I've done some hammer veneering but this is the fist time I'm using a vacuum bag. The question I have is how do you keep veneer from shifting on the substrate?

    I'm building a walnut sofa table...
  21. Thank you all. I was hoping that would be the...

    Thank you all. I was hoping that would be the consensus.

    Cliff
  22. Can I get away without a backer veneer?

    I'm building a sofa table for one of my daughters. I've got the parts cut and fitted and joinery done. It's not glued yet.
    405403

    I was looking through my odds and end the other day and ran...
  23. Replies
    13
    Views
    1,018

    It's also available for Android. I've been using...

    It's also available for Android. I've been using it for years. A great tool for the shop.

    Cliff
  24. Replies
    17
    Views
    2,317

    James, To actually answer your question, Lee...

    James,

    To actually answer your question, Lee Valley has a 90 degree magnetic guide along with dovetail guides. I have both and they work well.

    Cliff
  25. Rick, Here's what the store told me when I...

    Rick,

    Here's what the store told me when I bought my Sawstop. Get 2 2x12s and place them in the back of the truck. Have the store put the saw box on the boards lying flat nearest to the cab. When...
Results 1 to 25 of 340
Page 1 of 14 1 2 3 4