Search:

Type: Posts; User: Rangarajan Saravana kumar; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    1,589

    I had personal experience with Fiber on Black...

    I had personal experience with Fiber on Black Acrylic that the results far better finish with white appearance, and sharp than CO2 Engraver, and with 20w IPG earlier had good work with wooden...
  2. Yes cleaned bearings, rails, encoder

    Yes cleaned bearings, rails, encoder
  3. Sorry for my wrong interpretation.... when the...

    Sorry for my wrong interpretation.... when the laser takes the home postion, was running smoothly when a program sent. Suddenly at a particular point, it was stopping due to mechanical
    failure. I...
  4. Epilog laser lines while engraving not smooth - 24EX Legend

    Hi,

    My Epilog last week got faced a problem, suddenly stopped while running. So, i emailed to techsupport and suggestion is to tighten the y belt. After that, i tightened , new problem is
    the...
  5. Replies
    19
    Views
    3,058

    Fantastic Journey to continue with.... All the...

    Fantastic Journey to continue with.... All the best

    Regards
  6. I wish to have my rotary for fiber laser to get...

    I wish to have my rotary for fiber laser to get it used as almost 4 yrs over with that.. Bit scary

    regards
  7. Rdlc 320a controller problem?

    Hi,

    I have a chinese machine with laser controller RDLC 320A with recent problem , as i feel culprit in the controller.

    1. when i start the machine , it doesnt respond to move in either x axis...
  8. Replies
    8
    Views
    2,209

    If you have to engrave on metal , galvo i prefer...

    If you have to engrave on metal , galvo i prefer IPG pulsed laser 20w to 50w can be sufficient depending on your use... but there are lot others

    As i have limited experience with IPG laser, so...
  9. Replies
    8
    Views
    2,564

    Yes I agree the groove looks rough after bending,...

    Yes I agree the groove looks rough after bending, we do flame polishing inside the groove for 8mm, later bend

    no problem in look wise

    regards
  10. Replace cable and try again regards

    Replace cable and try again

    regards
  11. Still very curious to install a glass tube for my...

    Still very curious to install a glass tube for my epilog 50w legend

    Pls update with the photos

    Regards
  12. Hi, Glass tube, pls throw some detail of...

    Hi,

    Glass tube, pls throw some detail of replacing with Epilog tube

    regards
  13. I have a thought that the cutting takes more...

    I have a thought that the cutting takes more power with cost ratio in western machine rather chinese machines. So my suggestion is keep chinese for cutting rather engraving, because you
    might do...
  14. Replies
    15
    Views
    5,430

    Recently Rofin sinar has developed laser cutting...

    Recently Rofin sinar has developed laser cutting glass

    Search youtube cutting glass thru laser...

    regards
  15. Congrats Greg.. very nice to hear the addition....

    Congrats Greg.. very nice to hear the addition. All the best

    regards
  16. Hi, Earlier we had some erratic behaviour in X...

    Hi,

    Earlier we had some erratic behaviour in X axis and found that , the rod which carries the air hose, touch the x board seated on the flying optics and caused so many
    issues. After that we...
  17. I have had a lot of issues which any machine...

    I have had a lot of issues which any machine owner face like alignment, software update, tube, optics... Etc., goes on. But there comes excellent tech support to rescue us. I firmly advice to look...
  18. Replies
    138
    Views
    65,324

    I always had CMYK as defaut How to have RGB as...

    I always had CMYK as defaut
    How to have RGB as defaut?
    Thanks in advance
  19. See this if its helpful in pdf ... regards...

    See this if its helpful in pdf ...

    regards
    Saravana kumar
  20. Replies
    17
    Views
    3,053

    Excellent and stunning to see it flying.... tks...

    Excellent and stunning to see it flying.... tks for sharing

    Regards
  21. Replies
    23
    Views
    3,296

    See this could help you in corel 11

    See this could help you in corel 11
  22. Replies
    14
    Views
    2,053

    Ron, Did you use the corel trace? the finish...

    Ron,

    Did you use the corel trace? the finish seem to be very good? or any extra effort needed?

    regards
  23. Replies
    14
    Views
    2,053

    see if it is ok

    see if it is ok
  24. Replies
    14
    Views
    2,053

    sorry your file is not getting opened rgds

    sorry your file is not getting opened

    rgds
  25. i guess alignment in the machine mirror and lens...

    i guess alignment in the machine mirror and lens is required...

    regards
Results 1 to 25 of 145
Page 1 of 6 1 2 3 4