I am building my real workbench now, and in need for a good front vise.
Saw this Mophorn Woodworking Bench Vise 10.5 Inch on amzon, reviews seem to be good, just wondering If I go with this, will...
Type: Posts; User: Forrest Gon; Keyword(s):
I am building my real workbench now, and in need for a good front vise.
Saw this Mophorn Woodworking Bench Vise 10.5 Inch on amzon, reviews seem to be good, just wondering If I go with this, will...
thanks guys,I knew i would get some input here!
So does the wood color get more white or stay unchanged (like no finishing at all)
I have heard about using osmo 3051 on white oak so the end result is not the typical amble finish. But i could not find any photo or video to see what the result really is.
Wondering if anyone...
oh, yes, I forget to mention, the blade is 90 to the table, on the back and on the side.
I am not sure how to adjust the column...messed around a little bit and cannot find a way.
I recently bought a new rikon 10-3061 bandsaw and set it up according to the manual and various youtube video guides, have not done any real projects yet, but I just noticed that while everything...
for the velocity 20" floor fans, will it be better off placing it in the back of the garage, instead of at the garage door?
I do woodworking in garage while the two garage doors open, is there any good fan that I can use to help blow the dust out through the doors?
Right now I have got a costco pedestal fan, but it...
Just providing an update, I bought a new blade and now it cuts straight pretty well.
Thanks everyone for the great input, I appreciate it!
okay, here is another update,
Changing the blade position does not change much(if anything), i was putting the the deepest part of the gullet with the center of the top wheel, and moving the...
I watched this video and have followed all the steps and the result is still the same.
In order to rule out the possible alignment issue, I on purposely "rotated" the table as far as it could go...
Sorry I am a bandsaw noob, so I already need a new blade although the current one is brand new? 😂
My first bandsaw, a new rikon 10-3061, set it up according to the manual and various youtube tutorials such as Alex Snodgrass's method (align the blade, tension the blade, thrust bearings and side...
I am making 3 long floating shelves, (7.5 feet), the top, bottom, and middle section all are 45 miter, and with table saw, not matter how careful I tried, the end result of the long bevel board look...
Thanks guys, Ground Contact Pressure-Treated Plywood is the PWF you guys refered, correct?
I have got a very small concrete landing area (about 4ft x 4ft) which needs to covered by subfloor so laminated floor can be installed.
Can I just use some leftover loctite pl300 to glue a piece...
oh boy, i might just put back the old carpet ....:eek:
hmmm, the issue is "not" upper and lower stairs have difference riser heights.
No matter what I do, either the last step of the upper stairs OR the first step of the bottom stairs will not be the...
My basement staircase looks like this, a flight of stairs, then landing area, then another set of stairs,
465048
The whole thing was covered with carpet before, and I am removing the carpet...
As promised, here is the update, the stairs now are not squeaky at all now after using framing anchors. I used 6 anchors and they work pretty well. :)
Thanks everyone for the great inputs! I am...
Thanks guys, I will start with the framing anchors first, will be heading to the box store to get those in a little bit.
Will provide updates soon.
The space under the stair is a basement closet, (these are stairs going down to the basement).
I think at this point, we can tell the problem is the moving middle section between the two skirt...
Okay, hopefully the last question, please see the photo below, I was planning to screw the stringers to the stub through "A", but it seems that the A in the photo is actually skirtboard and the two...
Here are two photos, it seems that the fit between stringers and wall is pretty tight, I see no gaps I need to shim. If folks think the GRK rss rugged structure screws #10 x 3-1/8 is good, I will...
Hi guys, I have some GRK rss rugged structure screws #10 x 3-1/8.
Will that be sufficient to fix the stringers to the studs? Or I better go to HD to get the Ledger Board Fastener?
Thanks
Thanks, will probably do this first and see how it goes.