Search:

Type: Posts; User: glenn bradley; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.53 seconds.

  1. I have tried a few fences and realize that the...

    I have tried a few fences and realize that the "best" one will vary with the user. I always end up going back to basics which is an old Rockler. This is very much like Derek's example. The ability...
  2. Replies
    198
    Views
    25,992

    Of all the things that have happened with this...

    Of all the things that have happened with this project, for some reason I feel that this . . .

    465205

    . . . is a real milestone(???).
  3. Replies
    10
    Views
    388

    I would resaw the material yet again and use it...

    I would resaw the material yet again and use it as a veneer or an inlay. That way you get the look of the nice material and you get enough thickness to allow frame integrity.

    465203465204465202
    ...
  4. Replies
    33
    Views
    3,179

    Wait. How did I miss this the first time...

    Wait. How did I miss this the first time around!?! Nicely done sir. It must be really satisfying to have the whole set. Wonderfully matched. Clean lines. I don't miss the spindles at all.
  5. Replies
    30
    Views
    1,048

    My original Milwaukee 5625 is still running in...

    My original Milwaukee 5625 is still running in the table since it was installed in 2006.
  6. Another plus for the Lee Valley lipped bits....

    Another plus for the Lee Valley lipped bits. Downside is it’s not really feasible to sharpen them with their original profile so once dull they can be sharpened like a regular bit. That being said I...
  7. Replies
    8
    Views
    750

    I wonder if "just like" may need some...

    I wonder if "just like" may need some clarification. How about a quick snapshot?
  8. Replies
    198
    Views
    25,992

    Thanks guys! Got the drum sander in this...

    Thanks guys! Got the drum sander in this morning. It is surprising how much abrasives weigh if you get enough of them in a small space.

    ...
  9. Replies
    12
    Views
    578

    I have the very simple GLM20. It saved me so...

    I have the very simple GLM20. It saved me so much time when I was laying things out in the new place.
  10. Replies
    198
    Views
    25,992

    I skipped the alternate plan. Turned out I have...

    I skipped the alternate plan. Turned out I have plenty of room.

    464930

    The lift helped get the DP Wall Cab on the wall.

    464929

    Got an assist with the DP. The balance of the parts are...
  11. Replies
    11
    Views
    547

    Way too nice for shoes. Wonderful job.

    Way too nice for shoes. Wonderful job.
  12. Replies
    20
    Views
    991

    I have a 4" duct at the rear of the compartment...

    I have a 4" duct at the rear of the compartment and a door with holes in the front. Between the vents and the throat opening of the router (which varies with your insert) you want about the surface...
  13. Replies
    198
    Views
    25,992

    I hear ya. I've already saved several trips back...

    I hear ya. I've already saved several trips back and forth to the temp-shop. I made some progress on the wall to the right of the tool cabinet. I hung a lot of clamps here just to get them out of...
  14. Replies
    198
    Views
    25,992

    I unloaded the plane till so it could be moved. ...

    I unloaded the plane till so it could be moved. It is depressing to see this much dust on these things. Not that they don't normally get dusty . . . it's just that this is the wrong kind of dust...
  15. Replies
    198
    Views
    25,992

    Using a variety of MacGyver methods to avoid...

    Using a variety of MacGyver methods to avoid lifting anything heavy I got three whole cleats up on the wall yesterday :D. This is my tablesaw and router table jig wall. The jigs shown are just...
  16. My grizzly also allows the inlet and exhaust to...

    My grizzly also allows the inlet and exhaust to be installed in several orientations around the compass. If you truly want a left-handed psych loan then Clearview as the one I know of. I’m sure...
  17. Replies
    13
    Views
    742

    I have a few. Most used is 36 x 26 allowing for...

    I have a few. Most used is 36 x 26 allowing for 24 inches comfortably between the fences.
  18. Replies
    9
    Views
    795

    I'm with the other responders. I also have a...

    I'm with the other responders. I also have a Delta 1HP buried over in the corner somewhere, sleeping. Even with a properly sized aftermarket bag from American Fabric Filter (which did wonders for...
  19. Replies
    9
    Views
    506

    The first time I saw those an image of a horse...

    The first time I saw those an image of a horse with a seat belt came to mind. If you're one who puts a blade on and runs it to the end of its life the inconvenience would not be so great. If you...
  20. Replies
    198
    Views
    25,992

    Agreed. The ability to move through the shop...

    Agreed. The ability to move through the shop without having to do a carefully choreographed dance routine will be a bonus. Alas, the increased costs over the last couple years had me making tough...
  21. Cool idea John. Thanks!

    Cool idea John. Thanks!
  22. Replies
    198
    Views
    25,992

    It's funny . . . 464583 . . . these machines...

    It's funny . . .
    464583
    . . . these machines don't seem nearly as big as they did in the old shop.
  23. Replies
    198
    Views
    25,992

    I finished up the S-curve in the DC shed. The...

    I finished up the S-curve in the DC shed. The S-curve assembly was surprisingly stout once taped. Despite this I wanted some support in the event of an errant bump so I built a three point ...
  24. Replies
    198
    Views
    25,992

    Update - All is well on the port heights ;-)...

    Update - All is well on the port heights ;-)
    464491

    After percolating quite a while I decided that the pipe below the last wye could just fill with spoil as it may. The action of the dust...
  25. Replies
    198
    Views
    25,992

    The doc says I am off light duty and can move to...

    The doc says I am off light duty and can move to "medium" duty. I am also done with my PT which pretty much made every day useless for the last 2 weeks . . . sheesh! Moving on . . .

    I don't...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4