Search:

Type: Posts; User: Frank Martin; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.26 seconds.

  1. I am far from being an expert, but using hollow...

    I am far from being an expert, but using hollow grind and then Shapton stones, ending up with green compound on a planed piece of maple it has worked well for me. I adopted this approach based on...
  2. Thanks for the responses. I forgot to ask about...

    Thanks for the responses. I forgot to ask about the chipbreakers and great to hear I don't need to buy those, just the irons.
  3. Veritas PM-V11 irons for Lie Nielsen #4, #3 and #2 planes

    Most of my hand tools are Veritas, which I really like. Some pre-date the introduction of PM-V11 and I replaced most of the irons with that steel as I like it more than A2 or O1. I have several LN...
  4. Replies
    27
    Views
    1,978

    I am now able start the cyclone consistently on...

    I am now able start the cyclone consistently on another circuit. So, it is definitely the wiring problem created during the AC install on the original circuit. Thanks again for the help in...
  5. Replies
    27
    Views
    1,978

    I tried to run cyclone by connecting to another...

    I tried to run cyclone by connecting to another 230V outlet. It did start. I turned off quickly as I had disconnected it from ducting. Tried turning on again right afterwards, this time no...
  6. Replies
    27
    Views
    1,978

    Pictures show only the wiring on the cyclone as...

    Pictures show only the wiring on the cyclone as it came from Oneida 12 years ago. I will check the wire colors inside the outlet to see if a hot leg is white causing confusion to the HVAC guy.
  7. Replies
    27
    Views
    1,978

    I believe I found the problem. We recently had...

    I believe I found the problem. We recently had AC installed in our house. Contractor took power from the subpanel in my garage shop to connect power the AC unit. The outlet feeding the cyclone is...
  8. Replies
    27
    Views
    1,978

    Picture of the motor nameplate is attached to...

    Picture of the motor nameplate is attached to post #11. I don’t see anything about thermal protection on it. I measured voltage at the motor with one probe at a live connection, another to ground....
  9. Replies
    27
    Views
    1,978

    Any ideas on how to access this on the motor I...

    Any ideas on how to access this on the motor I have? I did not see a switch in the wiring box or where the capacitors are located. Do I need to disassemble the motor further to see this thermal...
  10. Replies
    27
    Views
    1,978

    I bypassed the switch entirely and direct wired...

    I bypassed the switch entirely and direct wired the motor. No response. Checked the capacitors, they look fine and when I measured the capacitance they both had readings in the correct range. Does...
  11. Replies
    27
    Views
    1,978

    Attached is the schematic for the switch. I have...

    Attached is the schematic for the switch. I have voltage at L1 and L3. When I force the contactors I get voltage all the way through to the cable to the motor. However, at no time the motor started...
  12. Replies
    27
    Views
    1,978

    Oneida Super Dust Gorilla - Not starting

    I purchased the 2.5 hp Onedia Super Dust Gorilla Cyclone in 2008 and have used it minimally since then in my hobby shop. When I attempted to run it today it did not start, no noise from the magnetic...
  13. Replies
    21
    Views
    1,320

    After being very happy with my Mirka Deros and...

    After being very happy with my Mirka Deros and selling my last remaining Festool sanders I purchased the following two Mirka DEOS sanders: 383 (rectangular) and 663 (delta). So far used the...
  14. Replies
    29
    Views
    3,042

    Peter, glad that you seemed to have resolved your...

    Peter, glad that you seemed to have resolved your issues. I second Derek's perspective. I have a Minimax CU300 combo and had to work on it several times (electrical components, primarily). While...
  15. Replies
    20
    Views
    1,358

    I am not into old iron either. However, purchased...

    I am not into old iron either. However, purchased a 1966 Rockwell drill press that had only one owner, apparently for hobby use. It even came with the manual. Upgraded few parts and really like it,...
  16. Replies
    41
    Views
    2,938

    I was into floating tenon joinery before Domino...

    I was into floating tenon joinery before Domino came out. I was making my own tenons back then. I purchased a Domino when it first came out. One of the upsides of this was not having to make my...
  17. I have not used it yet, but it seems to be high...

    I have not used it yet, but it seems to be high quality. I went with this because of higher capacity battery (CR123) and higher resolution compared to Wixey, etc. I have some low cost digital...
  18. It is Proscale 190-10. Normally $399, but they...

    It is Proscale 190-10. Normally $399, but they have been running a $100 discount for sometime.

    I used the standard bracket that came in the package. Had no idea that they may have special...
  19. I installed the Proscale digital scale this...

    I installed the Proscale digital scale this weekend. Here are some pictures in case it helps someone in the future. I will likely lower the readout a bit more in the future. Otherwise, I am pretty...
  20. Replies
    20
    Views
    920

    I have a 8” Forrest dado set for use in my...

    I have a 8” Forrest dado set for use in my sliding saw. Have been very happy with it. I purchased a 6” set with custom 1.25” bore for use in my shaper (part of the Minimax combo) as a groover. ...
  21. I paid the full price and would do it again in a...

    I paid the full price and would do it again in a heartbeat. They are well designed and manufactured.
  22. Proscale Planer Depth for Minimax CU300

    I purchased a Proscale to use as a planer depth gauge for my CU300. Trying to figure out the best place to install it. Ideal place is to have everything (encoder and the separate readout) on the...
  23. Hi Warren, Great ideas. I have done some TLC...

    Hi Warren,

    Great ideas. I have done some TLC on this machine recently as I could not use it while waiting for new dust ports, etc. One of the things I did was to replace black steel screws that...
  24. This ended up being very effective after...

    This ended up being very effective after significant amount of tapping with a ball peen hammer from under the insert.

    Thank you for the great idea, Warren!

    I ended up sanding the edges of the...
  25. Thanks for all the ideas. Tried the hammer...

    Thanks for all the ideas. Tried the hammer method and it is not moving at all. Put some oil around the outer edge (where the insert meets the cast iron top) to see if it helps loosen things up, but...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4