Search:

Type: Posts; User: Mike Kelly; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.23 seconds.

  1. Replies
    0
    Views
    127

    Behlen Salad Bowl finish

    Does anyone know where to purchase Behlen's Salad Bowl finish 603-0015. I think they have been bought by Mohawk. I have two very old pints but would prefer some a little fresher. I could probably...
  2. Replies
    57
    Views
    10,658

    Bruce, this was just a stain, not any finish or...

    Bruce, this was just a stain, not any finish or paint. Didn't have a problem with the Festool but I did with the PC.
  3. Replies
    57
    Views
    10,658

    Bruce, the hickory started out as bare wood and a...

    Bruce, the hickory started out as bare wood and a stain was added 4 times after it was taken back to bare wood to get rid of the swirl marks. The Festool sanders are so good with dust extraction that...
  4. Replies
    57
    Views
    10,658

    Thanks Mark. I turned the sander on while on the...

    Thanks Mark. I turned the sander on while on the board. (Both the ETS EC 150/3 and RTS 400.) I took it off the board before removing power. I cleaned between each grit with a vacuum of the sander...
  5. Replies
    57
    Views
    10,658

    341957 Here is what happened no matter what I...

    341957
    Here is what happened no matter what I did.
    The orbit is 3mm. Vacuum was at minimum and pressure just enough to guide sander.
  6. Replies
    57
    Views
    10,658

    I found this old link as I have been trying to...

    I found this old link as I have been trying to re-learn how to sand with a new Festool ETS EC 150/3 EQ. I was trying to finish a hickory project and kept getting swirls no matter what I did. I even...
  7. Rick, I have had a PC in my ShopBot for years. ...

    Rick, I have had a PC in my ShopBot for years. It started screaming at me yesterday so I replaced it with one I got off of EBay 4 years ago anticipating someday I would need it. Just needs bearings,...
  8. I also have an X10 220V appliance module to...

    I also have an X10 220V appliance module to control my 1.5 HP cyclone. I have gone through several of them. They fail and don't work at all, which is OK, but I have had them intermittently turn on...
  9. Been using Micro Jig products for years. Saved...

    Been using Micro Jig products for years. Saved my hands a couple of times for sure.
  10. Be nice to try these blades!

    Be nice to try these blades!
  11. Whiteside is my favorite

    Whiteside is my favorite
  12. Nice drill table

    Nice drill table
  13. I don't hve that one.

    I don't hve that one.
  14. Replies
    1,035
    Views
    82,275

    Nice Bandsaw!

    Nice Bandsaw!
  15. Replies
    872
    Views
    67,157

    Real Nice Drawing!

    Real Nice Drawing!
  16. Replies
    7
    Views
    5,425

    I asked their sales people twice on what the...

    I asked their sales people twice on what the accuracy and repeatability of the machine was and still do not know. I left the third strike hanging........ It may be a good machine, but they sent me a...
  17. Replies
    27
    Views
    5,602

    James and Zelma. If you are close to Austin, I...

    James and Zelma. If you are close to Austin, I can show you several ShopBot machines in the area. mikekelly at austin.rr.com I am in west Austin heading to Dripping Springs.
  18. Replies
    2
    Views
    999

    Good news. Thanks Guy, I had the same thoughts. ...

    Good news. Thanks Guy, I had the same thoughts. I tore it apart to see. It looks new inside and is real clean now. The plastic chips must have come from something I cut a long time ago. Nothing...
  19. Replies
    2
    Views
    999

    Hitachi M12V Issue

    I just did some maintenance on my M12V that has been in my router table for years. I had removed the springs a long time ago and was having trouble moving it close to the bottom of it's travel. ...
  20. Replies
    5
    Views
    2,046

    It looks like a Youngdale hinge. CSH has a...

    It looks like a Youngdale hinge. CSH has a complete selection. Make sure you know what you need before you order. There are several selections and sizes.
    ...
  21. Replies
    32
    Views
    32,098

    Wally Kunkel describes the same technique for...

    Wally Kunkel describes the same technique for building a super solid table top in "How to Master the Radial Arm Saw". Great idea. That phenolic plywood is pricy. You could laminate a top with...
  22. Replies
    32
    Views
    32,098

    Randy, your picture didn't come through....

    Randy, your picture didn't come through....
  23. Nick, you might want to look at a pressure foot...

    Nick, you might want to look at a pressure foot hold down from Wigetworks. They make a couple for different ShopBots and one that you can adapt to whatever machine you may have.

    ...
  24. Replies
    16
    Views
    2,086

    About a year and a half ago I "lost" my 18V...

    About a year and a half ago I "lost" my 18V Makita driver/drill. I had remembered putting it on the bumper of my truck while locking my shop up for the night so I thought it may have fallen off in...
  25. Replies
    13
    Views
    4,679

    Looks real good Kevin. Yours is the newer style...

    Looks real good Kevin. Yours is the newer style with the tube more firmly mounted at the table level it looks like, so the foot adjustment I did isn't necessary. Should last forever!
Results 1 to 25 of 264
Page 1 of 11 1 2 3 4