Search:

My son is a puzzler. I was over the other day and he is working on a Where's Waldo puzzle. Very confusing but I did find quite a few pieces to install while there.

I don't believe it does. I don't often tighten mine but if you do it may mushroom on the end easier than it does now. On the upside it will come out of the hole easier if it is mushroomed.

I removed the screw and found the threads were wearing because the quill was harder. I put the screw in the metal lathe and turned the threads off the end a little more than the keyway depth so it...

http://www.workersofwood.com/download/file.php?id=4761&t=1 http://www.workersofwood.com/download/file.php?id=4762&t=1

Different metals, iron, brass, aluminum, have different hardness and thus different turning characteristics and speeds. I have always felt the same about species of wood. I adjust speed to what...

If you have a threaded live center such as the OneWay Best Wood Tools will make an adapter for it. That's what I did.

https://bestwoodtools.stores.yahoo.net/

I'm assuming they are spindle gouges so you don't have to use the fixture. Just set them up like this.
...

Why not just but appropriate size band saw blade and use a length of it. Teeth are already set and sharp. I wonder though if they might be too aggressive for hand sawing.

The bolts spacing on my Penn State Ind chuck is a tad over 3/4".

I feel for you. I've lost knives in similar situations. I was given a couple Smith and Wesson spring assisted knives. I'm glad I didn't pay for them because the springs didn't last long before...

Walmart has these

https://www.walmart.com/ip/The-Write-Dudes-Gorilla-Lead-Edge-Mechanical-Pencil-1-8mm-2-Pack/44933641

https://pbs.twimg.com/profile_images/1130944374261637120/Ud5L2uT7_400x400.png

Wedge forks are used to remove car's tie rod ends. Look for one that may be the right size to fit between the live center and the shaft. I have used cold chisels as wedges for this job too.

...

467354 467356

There may be something going on. The Red Maple trees in this area are the last to lose their leaves and this year their leaves went first. Not just a tree here and there but everyone of them that...

I goofed in my earlier thread. Pewter is mostly tin.

I have in the past tried to freshen up Pewter items and found them to be hard to work with. I think if you try to solder it it may have a meltdown. 50-50 solder is 50% tin and 50% lead and melts...

I have heard of this before but I would have to wait and see how the Winter weather went to be able to tell which end is the head.

Live in Ohio now but grew up in Pittsburgh, Pa. We called them Monkey Ball trees. The fruit are said to be good for keeping spiders and other insects away. Put them around the basement floor. ...

Policeman Wins One!


A motorcycle police officer stops a driver for shooting through a red light. The driver is a real jerk, steps out of his car and comes striding toward the officer, demanding...

I bought a lightly used Grizzly G0657 on Craigslist a few years ago for $150.00.

It is a two speed drill and the swivel holds/locks the red drive gear in the hole. Remove the red drive gear and insert it in the other hole and the speed is changed.

In my neck of the woods they figure $1500 a day for a tree cutting crew. Lost all my ash trees 4 or 5 years ago. I have been doting on some small ash trees that have sprung up. I wonder if the...

Hand screw clamps employ screws with both right and left handed threads. Might be a good replacement if proper length and thread size could be found.

Also, may it have come from a buffing system?...

Never any fun that's for sure. Happened here a few years back. A shed which doesn't have electricity run to it took the hit and had the siding blown off one side. Traveled to the next shed and...