Search:

Type: Posts; User: glenn bradley; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.88 seconds.

  1. Iíll just caution that some chain paths involve...

    Iíll just caution that some chain paths involve more slack than one might think should be there. I would call grizzly and confirm what the chain path should look like when normal. There is nothing...
  2. Replies
    37
    Views
    1,381

    Too true. This is a perfect place to use an...

    Too true. This is a perfect place to use an aluminum and plastic jobsite saw.
  3. Here's a snapshot from the article:

    Here's a snapshot from the article:
  4. Replies
    8
    Views
    519

    The only trouble I have with rust in the desert...

    The only trouble I have with rust in the desert basin area is when the dew point hits and a layer of dust is on the cast iron surfaces. The dust holds the moisture and . . . well, you know. When I...
  5. Makita GCS Rail Connector Wrench Stash

    Maybe I'm just ham-handed but, it seems like half the time when I dump the rail connectors out of the little storage tube I drop the wrench. Makita did a good job of providing a storage spot for the...
  6. What is a car doing in your shop!?! :D I'm...

    What is a car doing in your shop!?! :D

    I'm with Jim. I never knew how much I enjoyed my detached garage shop with the door hidden until I moved into suburbia and had a shop with the door facing...
  7. Replies
    16
    Views
    627

    Good info so far. I have a 60T that I use for...

    Good info so far. I have a 60T that I use for hard woods like ash, white oak and maples. I switch to an 80T for softer things like walnut. Using a sled with ZCI's in the bed and the fence help. ...
  8. Replies
    32
    Views
    1,327

    I believe Jim is referring to direction of...

    I believe Jim is referring to direction of airflow versus the male/female connection.
  9. Replies
    14
    Views
    1,952

    Arise . . . oh long dead thread . . . and speak...

    Arise . . . oh long dead thread . . . and speak again . . .

    415494
  10. Replies
    7
    Views
    567

    Beautifully done. That will be a workhorse.

    Beautifully done. That will be a workhorse.
  11. Bingo. You have an example of empirical evidence...

    Bingo. You have an example of empirical evidence of this reality ;-)
  12. Replies
    39
    Views
    2,398

    I thought the post was funny and enjoyed it ;-)

    I thought the post was funny and enjoyed it ;-)
  13. Mops are great for irregular shapes but, not so...

    Mops are great for irregular shapes but, not so great at stock removal. That is, they are more of a 'finishing sander' than a 'shaping' sander. If you are just trying to knock the outer film off or...
  14. This falls under the "remodel" or "build new"...

    This falls under the "remodel" or "build new" scenario. As others have mentioned, building new is often easier and more effective than remodeling.
  15. Replies
    5
    Views
    535

    Another California Air fan here. Looks like the...

    Another California Air fan here. Looks like the Kobalt uses the same basic design. Isn't it nice to not jump out of your skin when the air compressor kicks on? There's just a sort of "thrummmm",...
  16. Replies
    4
    Views
    336

    I’ll have to look at mine but, with the fine...

    I’ll have to look at mine but, with the fine height adjustment threads engaged this should not be possible, yes?
  17. Replies
    9
    Views
    579

    Lee Valley’s triangle shaped burnisher makes this...

    Lee Valley’s triangle shaped burnisher makes this a breeze.
  18. Replies
    39
    Views
    2,398

    Congratulations. I’ll just say what I usually...

    Congratulations. I’ll just say what I usually say; after nearly 4 decades of dreaming in octal and hex I find imperial very relaxing mentally.
  19. Replies
    15
    Views
    840

    I don't run into the situation often and so use a...

    I don't run into the situation often and so use a low cost solution. Mine happens to be the DeWalt but other option are similarly proced. I use the short drills shown in split and brad point. ...
  20. Replies
    16
    Views
    1,169

    :d:d:d:d:d:d:d:d

    :d:d:d:d:d:d:d:d
  21. Replies
    4
    Views
    233

    I placed my front and end vice screws as far...

    I placed my front and end vice screws as far apart as I could.

    415104415105

    I have had no reason to question this choice ;-)

    If the 16" OC (or so) positions do not leave you enough jaw to...
  22. Replies
    26
    Views
    1,389

    Others can chime in but, I do not use a cabinet...

    Others can chime in but, I do not use a cabinet scraper as an initial surface prep tool. Taking one directly to unprepared surfaces would generally result in, for me, just what you are experiencing....
  23. Replies
    2
    Views
    225

    I agree that setting improper expectations for a...

    I agree that setting improper expectations for a tool/machine will lead you to dissatisfaction. Neither a powered panel saw nor a GCS is a table saw. Use them to break down or do work that will...
  24. Replies
    24
    Views
    1,609

    Ditto here as well .

    Ditto here as well .
  25. Replies
    31
    Views
    1,888

    This is an interesting thread. I have been...

    This is an interesting thread. I have been nothing but happy with the performance of my 19-38. There is a definite scope of operation.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4