Search:

Type: Posts; User: Ken Fitzgerald; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.50 seconds; generated 57 minute(s) ago.

  1. Replies
    2
    Views
    138

    Following a recent article in FWW, I purchased...

    Following a recent article in FWW, I purchased the hardware kit from Woodcraft, bought some hard maple and built a Moxon vice. I don't have a traditional woodworking bench. I have an assembly table...
  2. I continue to wrestle with the complexities of...

    I continue to wrestle with the complexities of the butterfly extension table I am building. Last week after arriving home on Monday, my wife and I just collapsed on Tuesday and Wednesday. I did get...
  3. Replies
    16
    Views
    925

    These or similar devices are what we used to move...

    These or similar devices are what we used to move MRI magnets through the halls of hospitals or clinics when we couldn't lift them directly into the scan room via a removeable roof for wall section....
  4. Replies
    16
    Views
    925

    I used those roller lifts a lot to move a CT...

    I used those roller lifts a lot to move a CT gantry through the halls of hospitals and clinics when intalling a new one and removing old ones.

    A gantry can weighed 3,000-4,000 pounds.
  5. Replies
    16
    Views
    914

    James, every piece of apple I turned ended up...

    James, every piece of apple I turned ended up splitting. Granted, I haven't turned that much apple but so far it's been unanimous! And, that's a shame because the character of the wood is often very...
  6. Replies
    13
    Views
    981

    I am glad to hear that!

    I am glad to hear that!
  7. Please recommend a wipeon dining table finish.

    I have no desire to get into spraying.

    The new dining table I am building is black walnut. I prefer to use wipeon finishes. I have experience and good results with Min-Wax fast drying poly and...
  8. Replies
    35
    Views
    2,528

    Before we left town 2 weeks ago, I honed my 3/8"...

    Before we left town 2 weeks ago, I honed my 3/8" mortise chisel and bit, installed them in my GI mortiser and mortised 2 walnut table legs. I diamond hone the outer wall of the chisel flat, the...
  9. Replies
    12
    Views
    1,677

    You might try putting a ferrite choke on the air...

    You might try putting a ferrite choke on the air cleaners power...
  10. Replies
    33
    Views
    3,509

    The corporation and the buying public holds the...

    The corporation and the buying public holds the keys for the franchisees. Should WC become an online store only, I for one, will miss having a local store even though it is 100 miles away. I am a...
  11. Replies
    21
    Views
    4,289

    If you look at the screen shot of my table top...

    If you look at the screen shot of my table top plan, the breadboard edges will run the length of the table, down each side. Where the field boards meet the breadboard edge, I am toying with the idea...
  12. Replies
    0
    Views
    424

    Now I know...

    why I have a shop! As feeble as my attempts at building quality furniture may be, they more than justify the expense I have incurred over the last 20 years.

    I am 683 miles from home, experienced...
  13. Replies
    20
    Views
    1,602

    The first corporation I worked for had us sign...

    The first corporation I worked for had us sign one. 18 months later when a bunch of employees quit and started competing companies, the privately-owned corporation sued and lost in several courts.
  14. Replies
    8
    Views
    1,012

    I am 683 miles from home. I awoke thinking about...

    I am 683 miles from home. I awoke thinking about pitching the big box of industrial strapping tape and its metal clasps when we get home. I haven't shipped any large heavy boxes since I retired 13...
  15. Replies
    7
    Views
    1,149

    Nicely done, Glenn!

    Nicely done, Glenn!
  16. Replies
    79
    Views
    7,205

    As Jim suggested, build your top and edge it...

    As Jim suggested, build your top and edge it first. Then adhere your laminate. Then route the laminate and edging. I used a 45* chamfer bit, chamfering both back slightly. When you lay your laminate,...
  17. Replies
    8
    Views
    981

    That is scary!

    That is scary!
  18. Replies
    15
    Views
    1,162

    Looks great and well thought out tome Kent!...

    Looks great and well thought out tome Kent! Nicely done, Sir!
  19. Replies
    28
    Views
    2,988

    You might consider building a frame with 1/4"...

    You might consider building a frame with 1/4" dadoes in the sides. Make shelves out of 1/4"hard board and mount the containers to the shelves.
  20. Replies
    61
    Views
    6,015

    For over 40 years I repaired equipment, first in...

    For over 40 years I repaired equipment, first in air traffic control centers, then on fast attack submarines and the last 34 years in radiology departments in hospitals and clinics. I took up wood...
  21. Last week I managed to get all of the table top...

    Last week I managed to get all of the table top field pieces and the breadboard edge pieces planed to their final thickness. They are currently stickered. I began mortising the table legs. We are out...
  22. Replies
    79
    Views
    7,205

    My outfeed table top is double 3/4" plywood glued...

    My outfeed table top is double 3/4" plywood glued and screwed with plastic laminate on top. Love it! Glue drips clean easily. It's white so periodically I may sketch something out on it.
  23. Replies
    61
    Views
    6,015

    Over the last 3-4 years, I have purchased 3 Wood...

    Over the last 3-4 years, I have purchased 3 Wood River hand planes (a shoulder plane, low angle block plane and #4 1/2 smoother) , a 1" Veritas bench chisel, a set of Wood River bench chisels, glass...
  24. Replies
    21
    Views
    4,289

    Here's a photo of the 4 octagonal table legs....

    Here's a photo of the 4 octagonal table legs. They have a 5" tapered foot above which is a 3" turned area. If you look closely at the leg on the left you'll notice the turned collar on that one is...
  25. I think this is the norm for most large power...

    I think this is the norm for most large power tools. They send an average quality blade with the tool to get the new buyer started. For reason of being cost competitive, they don't send a higher...
Results 1 to 25 of 497
Page 1 of 20 1 2 3 4