Search:

Type: Posts; User: Jerome Stanek; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    32
    Views
    1,340

    I have both and the stand alone is much nicer to...

    I have both and the stand alone is much nicer to use.
  2. Replies
    32
    Views
    1,340

    I just had a update on my control computer even...

    I just had a update on my control computer even though I have updates turned off and it messed up my control software I had to roll back and reload my software. Bad thing was I went to start the cnc...
  3. Replies
    23
    Views
    782

    I have been wearing Redwing work boots for the...

    I have been wearing Redwing work boots for the last 30 years and they hold up good and I am rough on shoes. I had Wolverine that only lasted 1 year but I can get 3 years out of a pair of Redwings
  4. Have you looked at this one. ...

    Have you looked at this one.

    http://www.talkshopbot.com/forum/showthread.php?25161-FOR-SALE-BENCHTOP-24X32-w-RBK-upgrade
  5. Replies
    14
    Views
    938

    I don't think I ever had a bad experience at a...

    I don't think I ever had a bad experience at a Menards. I have gone to maybe 100 different ones all over when I was installing drug stores going back to 1995. I did like Builders Square and Home...
  6. Replies
    72
    Views
    2,744

    Will the base fit along with the CNC

    Will the base fit along with the CNC
  7. Replies
    14
    Views
    586

    It depends on the Plexi Cast cuts nicer then...

    It depends on the Plexi Cast cuts nicer then extruded when you use a fine tooth blade Extruded gums up more
  8. Replies
    72
    Views
    2,744

    I would take the trailer just in case. There is...

    I would take the trailer just in case. There is a saying that we use. It is better to look at it then look for it when we did trade shows. I always liked to be prepared for the unforeseeable
  9. Replies
    14
    Views
    938

    I go to a lot of different Menards there is on...

    I go to a lot of different Menards there is on Brookpark road in Brooklyn OH, Avon OH, Mansfield OH Massillon Oh and the one In Cuyahoga Falls Oh the only one I haven't been to is the Cuyahoga Falls...
  10. Replies
    39
    Views
    2,678

    I see you did just that

    I see you did just that
  11. Just try downloading the working demo and play...

    Just try downloading the working demo and play with it. You can do about anything except make your cut file and you can save it and when you buy a working copy your saved file should work.
  12. My CNC control computer is a pentium d 2.8 with 4...

    My CNC control computer is a pentium d 2.8 with 4 gigs of ram that I have Aspire on and it runs it ok Vcarve doesn't need as much as Aspire
  13. Replies
    39
    Views
    2,678

    I just saw 2 Blue poly barrels along side the...

    I just saw 2 Blue poly barrels along side the road with a free sign on them. If I needed one I would have stopped. They are just west of Medina Ohio on Smith road
  14. Replies
    8
    Views
    1,119

    Are you sure it is that router

    Are you sure it is that router
  15. Replies
    29
    Views
    977

    we used concrete expansion joint material for...

    we used concrete expansion joint material for this.
  16. Replies
    6
    Views
    414

    Go to lets talk shopbot and see what is listed in...

    Go to lets talk shopbot and see what is listed in the for sale
  17. I some times use a netbook with vcarve pro and it...

    I some times use a netbook with vcarve pro and it runs ok. My design computer is an I3 that has 8 gigs of ram and never needed more
  18. Replies
    34
    Views
    1,924

    I have to go there today to get some cut off...

    I have to go there today to get some cut off wheels
  19. Replies
    13
    Views
    938

    No just they will ban evil lasers that can cycle...

    No just they will ban evil lasers that can cycle faster then 1 dpi
  20. Replies
    7
    Views
    604

    I always required half down and if the job was...

    I always required half down and if the job was more then 3 weeks I would get draws. That way I was covered if they didn't pay at the end. I only had one customer that was bad at paying and I only...
  21. Replies
    39
    Views
    1,310

    My brother in law chose a trade it was concrete...

    My brother in law chose a trade it was concrete and after about 15 years his knees and back gave out so he went to cosmetology school and became a hair stylist he then went on to get his owners...
  22. Replies
    52
    Views
    3,315

    Sounds like Festools are to be used like a butter...

    Sounds like Festools are to be used like a butter knife on a steak. As for routers the Porter Cable 7518-19 are pretty much the strongest out there and will out last most other brands
  23. Replies
    39
    Views
    1,310

    I wore a few different hats over the years. When...

    I wore a few different hats over the years. When I was in high school I worked in a greenhouse picking tomatoes, I then went into printing and was a cameraman stripper plate maker then into...
  24. Replies
    52
    Views
    3,315

    The difference is a Hilti or Metabo will last you...

    The difference is a Hilti or Metabo will last you a life time with abuse. I have some Hilti and Metabo tools that are 35 plus years old and they traveled the country with me being used about 3 time...
  25. That should be the last thing after you get the...

    That should be the last thing after you get the sub panel and installed but before you take the cover off the main panel.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4