Search:

Type: Posts; User: Prashun Patel; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.30 seconds.

  1. Wood Turners Wonders They make 3 double-sided...

    Wood Turners Wonders

    They make 3 double-sided discs (I have them all)

    80/150, 360/600, 800/1200.

    One could argue that if you finish on stones, you really only need the lowest one.

    The 360...
  2. I can tell you that in my warehouse we had a...

    I can tell you that in my warehouse we had a situation with a 5 gallon bucket had a smidge of oil left at the bottom. Another 5 gallon bucket was loosely stacked on top. This was sometime in the...
  3. Replies
    23
    Views
    1,560

    A rasp is nice for shaping when a plane or...

    A rasp is nice for shaping when a plane or spokeshave wonít fit or canít handle the grain.

    Floats are used more by plane makers although some people use them (or a rasp) to tweak a joint as a...
  4. Roger is experienced and normally I wouldnít...

    Roger is experienced and normally I wouldnít challenge, but I personally wouldnít throw even gloves or mixing cups in an enclosed trash. I have had a warehouse fire start from a drying oil.
    ...
  5. Replies
    5
    Views
    412

    Your scratches can be from a couple things. ...

    Your scratches can be from a couple things. Sometimes the scratches from the lower grits arenít removed properly and then show up only when the surface starts to build a sheen. Sometimes once a...
  6. Replies
    8
    Views
    1,066

    Bringing the tailstock live center up to a...

    Bringing the tailstock live center up to a faceplate is a fine technique for centering the the turning as you reverse it.

    However, the taper of the live center only mates to the rim of the...
  7. I would contact Pete Terbovitch @ Horizon Wood...

    I would contact Pete Terbovitch @ Horizon Wood Products. He's in PA, though. What you should ask for is if he has pieces that are partially dried or haven't gone into kiln yet. I've been able to...
  8. While not on topic, I will add that for me that...

    While not on topic, I will add that for me that the two reasons I prefer cbn over white wheels are that the wheel diameter does not change and that they tend to run more true which means they never...
  9. Replies
    12
    Views
    857

    If you really think this not a dangerous idea, I...

    If you really think this not a dangerous idea, I would look at ash. Straight grained ash. Itís light and strong. Thatís why itís used for guitar necks and baseball bats.

    However, if you...
  10. Replies
    7
    Views
    867

    Isn't "weed pot" redundant? ;) Nice work. ...

    Isn't "weed pot" redundant? ;)

    Nice work. I'm partial to the last one. Feels sculpted from a block
  11. Wood Turners Wonders. Not cheap, but like you,...

    Wood Turners Wonders. Not cheap, but like you, I prefer the flat surface for plane blade grinding. I also work with a drawknife and find sharpening on the ws disc easier than other methods.
  12. Mike. Btw, they make cbn discs for the...

    Mike. Btw, they make cbn discs for the worksharp. Even better than the diamond lap discs .
  13. Replies
    34
    Views
    4,397

    Is your product oil based? The 8000cv is...

    Is your product oil based? The 8000cv is waterbased. So I am not sure the two products share much in actual practice.
  14. Replies
    34
    Views
    4,397

    Months. Are you using the same product?

    Months. Are you using the same product?
  15. Replies
    34
    Views
    4,397

    Yes Mark. In fact it did go away. I tried...

    Yes Mark. In fact it did go away. I tried using a hair dryer at first and that did not work. Time worked. It looks perfect now.
  16. Replies
    29
    Views
    2,631

    Derek, I think you just spoiled LV's April Fool's...

    Derek, I think you just spoiled LV's April Fool's Day item for 2023!!!

    They could have offered a protective, replaceable veneer inserts and different sizes for each plane. Still better, there...
  17. Replies
    29
    Views
    2,631

    Resting them on a bench I dont care if the bench...

    Resting them on a bench I dont care if the bench gets scratched. Resting them on any other surface that might damage the blade or be damaged by it, I use common sense.
  18. I had that DW735 for several years. My advice: ...

    I had that DW735 for several years. My advice:

    Get an aftermarket $20 single stage bag and run a short section of 4" pipe from the exit port to it, so the bag is just out of the way of the feed...
  19. Lukeís statement to think like a hand tool worker...

    Lukeís statement to think like a hand tool worker is rich.

    The shooting board helps you sneak up on the length. Itís not for the guy using a table saw to make 30 pieces of identical length. In...
  20. Replies
    8
    Views
    818

    You can apply multiple coats of blo in a day as...

    You can apply multiple coats of blo in a day as long as the previous coat isnít tacky. Always wipe completely off (sure you already knew that).

    I shellac my handles. Not so much as to build a ...
  21. Replies
    43
    Views
    3,586

    I am also in a funk. As a hobbyist, how many...

    I am also in a funk. As a hobbyist, how many tables, bowls, guitars, cutting boards, etc can one make? It's just the same old stuff over and over again. The way to make it fresh is to pick a...
  22. Replies
    49
    Views
    3,962

    I've done it both ways. It doesn't matter in my...

    I've done it both ways. It doesn't matter in my experience.
    I pay way more attention to the flatness.

    In fact, there is an argument to be made that doing one surface only, then smooooshing the...
  23. Replies
    13
    Views
    1,272

    I would not rip. Thereís good history on these...

    I would not rip. Thereís good history on these boards. Let them be different colors. Over time they may even out. They may not. So what? Love the one youíre with.
  24. That's going to be beautiful! The ambering...

    That's going to be beautiful!

    The ambering effect of a topcoat comes from oil-based topcoats, which traditionally have been used. Water-based topcoats do not have an amber effect. There are good...
  25. Replies
    21
    Views
    1,605

    You sound like me in terms of project types. I...

    You sound like me in terms of project types. I have never missed a larger sander. I have a 5Ē. If anything, there are way more times I need a smaller sander for concave parts like bowls .
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4