Thanks for all the replies. The molding is about 2" tall and the longest piece (front of the bar) is about 9 feet and will have 4 notches. The two side pieces are about 13" and get one notch each. I...
Type: Posts; User: Dennis Jarchow; Keyword(s):
Thanks for all the replies. The molding is about 2" tall and the longest piece (front of the bar) is about 9 feet and will have 4 notches. The two side pieces are about 13" and get one notch each. I...
I need to apply a cherry panel molding around a bar under the granite bar top. There are six 2.5" x .5" steel supports around the bar supporting the top, four in the front and two on the sides. I...
Thanks for the replies. I do strain the finish with a filter as Jamie suggested. I replaced both the air divider and air diffuser seals before spraying. I normally soak the metal parts in lacquer...
I have a Fuji Minimite4 with the T70 siphon gun. The gun is about 7 years old. The needle packing is original to the gun, but I haven't seen any leaking from it. This week I was spraying Target...
I am priming some poplar pantry doors and one of them developed a split on the rail along the grain. Door was primed with Target HSF500 sprayed at 3 mils. It didn't appear until I sprayed so it...
I applied some more stain like a glaze with a fine brush and then used a dry brush to blend it in. That minimized the differences. While not discounting sanding too much (I have a little of that on...
Plywood is combi core so there are mdf layers under the veneer and then veneer core in the middle. I used the same sanding sequence I used on the rest of the column and all of the other cherry...
I had a bunch of cherry cabinet and bar parts stained and sprayed by a finisher at his shop. I had to stain the tops of the cherry columns on the bar myself as they surround steel columns and the...
if you don't have one already, get a wet film measuring gauge. Better paint stores have them, or you can order off amazon....
Just to clarify, chairs for a 36" high table are called counter height chairs and the seat is usually 24" high. Bar stools are for an ~42" surface and the seat is 30" high. I am shopping for bar...
Kevin, thanks. I had a guy I know with a commercial shop machine the lock miter for me using a couple shapers with power feeders. he keeps them dedicated to just lock miters.
Kevin, thanks for the reply. I appreciate it.
I have to glue a long lock miter on an 84" cherry pantry cabinet finished end panel and the face frame before I send them to the finisher. It isn't ideal but the face frame and end panel will not be...
I had the same problem with my old Ridgid saw with the granite top. I would get everything dialed in and the next time I would check it, the alignment was off. Finally figured out it was moving it...
Yes that is one I have
Tom, I did measure both hot to ground and neutral to ground. Both were as expected. I also tried both sanders in outlets on different circuits.
Jim, I don't have one but can get one over the weekend.
Yes but going from 1-6 on the speed control only change the measured voltage by 10% or so.
Bill, I measured again on dc and the reading was in the milivolts. Constant 30v ac is at multiple spots on both sanders when running including the large casting the side handle threads into. I also...
Tom,
I am sorry to hear about your mother. I hope she is OK. No worries about getting back to me, you have more important things to worry about.
Yes, I just tried both sanders on a different...
Tom, my replacement from Amazon just showed up and I can also measure 30 volts AC between the screw on top of the sander where you rest your hand and ground. Do you have a multi-meter and could you...
I checked the outlet for a reversed neutral and hot. Voltages between hot and ground and neutral to ground were as expected.
Then I measured the voltage between the screw where I was getting the...
Bill, I assume since it is a two prong plug it is double insulated. I will check it tomorrow and will connect a multi-meter to the screw and the ground on the outlet it is plugged to as well.
I just bought the Bosch dual mode 6" sander. I used it for the first time tonight and I was getting shocks from it when I would touch a screw on the top of the sander. It didn't seem like a...
I have the Dewalt cordless as well. It does a decent job and as David says is ready to go as quickly as you can snap on a battery. It is not a replacement for my Festool sander in terms of dust...