Search:

Type: Posts; User: Jim Andrew; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.29 seconds.

  1. Replies
    11
    Views
    403

    If you could snap a level line on the wall behind...

    If you could snap a level line on the wall behind the cabinets, You could cut a 2x2 or 1x2 and fasten that to the wall at the rear, floor level only level. That would give the cabinets a level edge...
  2. Replies
    20
    Views
    549

    Agree with Jim. If anything make it 2' wider and...

    Agree with Jim. If anything make it 2' wider and 4' longer.
  3. Replies
    12
    Views
    254

    I have a general purpose vise bolted to a bench...

    I have a general purpose vise bolted to a bench top. It has a flat area behind the vise for the purpose of providing an anvil type surface. I hammer my crimps out on that. You also need a hand...
  4. Replies
    9
    Views
    445

    Bryce, when you figure out what spring you need,...

    Bryce, when you figure out what spring you need, would you please post the results. I also have about that same model drill press.
  5. Replies
    3
    Views
    143

    The only wood filler I have found that really...

    The only wood filler I have found that really holds is bondo. Have tried about every other product available over the years, but none work like bondo. Far as coloring it, I use a permanent marker,...
  6. Replies
    8
    Views
    260

    If your threads are stuck, try soaking with some...

    If your threads are stuck, try soaking with some motor oil. I would just put a few drops on, then add a couple every time you go in the shop. Takes a while sometimes. I have heard that the lemon...
  7. Replies
    20
    Views
    549

    If I were to put a basement under my shop, would...

    If I were to put a basement under my shop, would consider putting styrofoam under the floor and on the walls. That would go a long way to moderating the temperature in winter, and keep a lot of...
  8. My '04 unisaw has a sloped bottom inside the...

    My '04 unisaw has a sloped bottom inside the cabinet, and with a shark guard my DC gets all the dust, unless a stick falls into the cabinet and plugs the outlet. Don't need to mess with the air...
  9. The Bosch Ros 65vc I have is an awesome sander. ...

    The Bosch Ros 65vc I have is an awesome sander. The VC stands for vibration control, and the 65 means it can be 6" or 5". It can easily be used with one hand, and has a dial speed control. I use...
  10. If you want a helical cutterhead, Grizzly sells...

    If you want a helical cutterhead, Grizzly sells them to fit other brands.
  11. Replies
    9
    Views
    570

    I have a pile of old magazines, thinking maybe I...

    I have a pile of old magazines, thinking maybe I will need to look at them to find a project to build, but never seem to need to look, always someone wanting something. I have been building chests...
  12. Thread: Sandpaper

    by Jim Andrew
    Replies
    14
    Views
    474

    I bought some close out discs from Klingspor, and...

    I bought some close out discs from Klingspor, and they are good, but their new discs are much better. The newer ones I have are blue colored, the old ones were a orange color. Price was right on the...
  13. Replies
    8
    Views
    367

    If you don't mind using snap lock pipe, Ace...

    If you don't mind using snap lock pipe, Ace Hardware has 26 gauge pipe and fittings. I only found T's and no Y's, would have to source Y's elsewhere.
  14. I talked to Grizzly about my G9983 wide belt...

    I talked to Grizzly about my G9983 wide belt sander, and since they moved to a new model, they are no longer supporting the G9983 with parts. They can help you a bit, but not all parts. ...
  15. Replies
    9
    Views
    289

    Have you tried putting some oil on the threads? ...

    Have you tried putting some oil on the threads? My old Cman table saw had to be oiled occasionally.
  16. Sounds like it would really limit your ability to...

    Sounds like it would really limit your ability to re-arrange your shop. I have moved things around since first setting up the shop, much better the 2nd or 3rd time. I have no reason to move my...
  17. I have a LED worklight, that could be plugged in,...

    I have a LED worklight, that could be plugged in, it is made to set on floor or on top of a cabinet. Higher light is better. A neighbor uses a ceiling shop LED light portable, he just leans it...
  18. I had a couple of Ryobi tools, thought they were...

    I had a couple of Ryobi tools, thought they were ok, then got a couple duds. Have they cleaned up their act?
  19. Have you looked at the G0846? I would buy that...

    Have you looked at the G0846? I would buy that one, but already have the G0540, which works fine for mortises as long as you don't need angles. Both are floor models.
  20. Please post when you get this figured out. That...

    Please post when you get this figured out. That planer is a commercial grade, and I have considered it a couple times.
  21. I changed out the panel in my shop, had an...

    I changed out the panel in my shop, had an electrician for a neighbor, he just explained how to do it over the phone. Be sure to turn off the power before you start. I had to do mine hot.
  22. Replies
    11
    Views
    424

    I built on a store room, has my DC, air...

    I built on a store room, has my DC, air compressor, tire machine, and lumber and plywood storage. Just added to the length of my building. Would think adding a lean to would be fairly easy to house...
  23. I brush off with a broom, then if still dirty,...

    I brush off with a broom, then if still dirty, take a glue scraper to it. I file the glue scraper to keep it sharp.
  24. I bought a small widebelt sander to sand panels...

    I bought a small widebelt sander to sand panels after gluing. Also works for sanding panel doors if I use 7/8" thick frame material. Cauls help get your panels flat and even enough that you don't...
  25. Replies
    12
    Views
    641

    Sounds like a good reason to buy a Grizzly.

    Sounds like a good reason to buy a Grizzly.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4