Search:

Type: Posts; User: Jamie Buxton; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.46 seconds.

  1. Replies
    8
    Views
    167

    If what you need is a pressure-treated flat...

    If what you need is a pressure-treated flat plate, you might consider starting with pressure-treated plywood, and laminate enough layers to get the thickness you want. I understand that the mill...
  2. I bought my 3/4" non-continuous coupling nut...

    I bought my 3/4" non-continuous coupling nut from McMaster Carr. However, what I bought was an extra-long version which is 5" long. Now that I look at the product detail, the threading is...
  3. Here's a complete rack --...

    Here's a complete rack -- https://www.wwhardware.com/kv-undercabinet-pull-down-cookbook-rack Further down the page, they'll sell you just the hardware.
  4. I too bought 3/4” couplings. They were 5” long. I...

    I too bought 3/4” couplings. They were 5” long. I built a whole piece of furniture presuming that threads ran straight through. But when I attempted the final assembly, I found that the threads...
  5. Epoxy first. You're going to sand the cured...

    Epoxy first. You're going to sand the cured epoxy down flush to the wood. If you stain the wood first, you'll likely sand through some of the stain.
  6. Replies
    12
    Views
    476

    Well, Festool has "solved" that issue by...

    Well, Festool has "solved" that issue by including a Bluetooth connection from the tool to the vacuum. Rather than modifying the tools, they put the bluetooth radio in the battery.

    But I don't...
  7. True, but from my supplier, the 5x5 is precisely...

    True, but from my supplier, the 5x5 is precisely 60"x60" within 10 thousandths, and the 4x8 is similarly precise. That'd be 152mm by 152 mm, and 1219 mm by 2438 mm. I think the stuff is cut at the...
  8. Replies
    9
    Views
    208

    You can buy extrusions designed to house LED...

    You can buy extrusions designed to house LED tape, and from the same sources you can buy opal diffusers which clip on to the extrusion. Like Peter says, you do want the diffuser. Lee Valley is one...
  9. Replies
    4
    Views
    246

    Yeah, cut them down. A hacksaw does the trick.

    Yeah, cut them down. A hacksaw does the trick.
  10. Replies
    7
    Views
    430

    I'm mostly a power tool guy, but that task can be...

    I'm mostly a power tool guy, but that task can be done quickly and accurately with a hand plane. Mark the desired curves on the top and the bottom of the leg. Clamp the leg so that you can run the...
  11. There's a saw specifically designed to cut that...

    There's a saw specifically designed to cut that underlayment right at the face of the toekick. Google "toekick saw". Tool rental places have them.
  12. Replies
    20
    Views
    1,011

    Space might be a consideration for you. You can...

    Space might be a consideration for you. You can install a router table as a wing on the table saw, so it doesn't take up any floor space at all. The shaper does take floor space.
  13. Replies
    5
    Views
    363

    Scott, where your photos should be, I only see a...

    Scott, where your photos should be, I only see a "broken" icon which says that something is missing.
  14. Replies
    9
    Views
    354

    The common piano hinges are supplied with teensy...

    The common piano hinges are supplied with teensy little screws - #4 by 1/2” - and the leaves are made of metal thinner than a credit card. That’s not strong enough for this bench.
  15. Replies
    9
    Views
    354

    You might also want to consider what holds the...

    You might also want to consider what holds the seat up in the air when you open it. Of course, you can hold it with one hand while you rummage below with the other. But it is more convenient if...
  16. Replies
    9
    Views
    354

    Depending upon exactly what you're trying to do,...

    Depending upon exactly what you're trying to do, knuckle hinges may not need to stick up above the seat surface. You can set the hinge flush with the seat surface if you relieve the parts being...
  17. Replies
    14
    Views
    475

    I have a three stage turbine made by Accuspray. ...

    I have a three stage turbine made by Accuspray. It works well for clear finishes. It can spray pigmented lacquer. It even can spray what the housepaint stores call acrylic trim paint, although I...
  18. Replies
    9
    Views
    495

    Wood Slicer, from Highland Hardware. ...

    Wood Slicer, from Highland Hardware. https://www.highlandwoodworking.com/woodslicer-resaw-bandsaw-blades.aspx
  19. Replies
    12
    Views
    426

    Yeah, I use 5-minute epoxy as wood filler. I...

    Yeah, I use 5-minute epoxy as wood filler. I load it with sanding dust from the species I'm working on. The color match is usually okay. It doesn't look like the natural wood -- it is all just...
  20. Replies
    13
    Views
    901

    I've bought other kinds of LED lighting from...

    I've bought other kinds of LED lighting from superbrightleds.com. If you're thinking of tube-style shop lights, here's a page with a bunch of lights with 6000 lumens or more: ...
  21. Replies
    3
    Views
    419

    Filler cures hard -- to the point that you can...

    Filler cures hard -- to the point that you can sand it. Putty stays soft for a long time. It never gets hard enough to sand.
  22. James, a pic would be very good.

    James, a pic would be very good.
  23. Replies
    4
    Views
    229

    You might be right. But really what those...

    You might be right. But really what those diagonal supports do is prevent racking. They'll do that job in either design.
  24. Replies
    2
    Views
    142

    Cover for wood patio table?

    I'm working on a big patio table -- twelve feet by four feet. The people I'm building it for would like a shiny surface like what's on their indoors furniture -- y'know, varnish. I don't think they...
  25. That's an interesting product. I wonder how...

    That's an interesting product. I wonder how many of them they'll actually sell. Their customer is somebody who wants an unusual high-end loudspeaker, but has no woodworking capability, and...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4