Search:

Type: Posts; User: Warren Lake; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.26 seconds.

  1. I cant label technique on a jointer any one way...

    I cant label technique on a jointer any one way as it changes for different material and what is is. Pork chop usless if im dropping on long stock. Traction I get on a board different was well....
  2. 40 years jointing material never had a board ...

    40 years jointing material never had a board "shatter" you mention it repeatedly. At one point I jointed so much rough red oak that my palms were like a roofers knuckles. Any roofers will get...
  3. This is an interesting set up. 457512 ...

    This is an interesting set up.

    457512

    Dragging back done it more times than I can remember. Its likely mostly to longer stuff. There is no launch least not my high speed steel knife stuff...
  4. Replies
    50
    Views
    3,001

    never had a need for a brake on a saw or any...

    never had a need for a brake on a saw or any other machine for that matter, when I shut off a jointer or whatever it winds down and stops.

    On my older machines different than this electronic...
  5. Replies
    8
    Views
    541

    too long for me to remember but thinking vynl...

    too long for me to remember but thinking vynl wash which we used to use before RM Epoxy then Imron after. I stripped car parts in strong reducers one time the imron fell off, the RM epoxy fell off...
  6. Ken you were right on the rotate thing, I asked...

    Ken you were right on the rotate thing, I asked and he said yes it went to about 1980., He said on mine its a rectangle so you do a full rotation. i could have done that but want it rebuilt, he saw...
  7. Replies
    43
    Views
    4,132

    I dont too many burned out might be better now...

    I dont too many burned out might be better now but the taste remains. Not close the the porter cables.
  8. Bill 12 volts to the starter and it jumped and...

    Bill 12 volts to the starter and it jumped and ran fine

    12 volts from the battery right to the small termial and nothing, I think the solenoid should have fired and I would have heard it
    ...
  9. Replies
    43
    Views
    4,132

    had a whole heard for a while. Tons of Makita....

    had a whole heard for a while. Tons of Makita. Have the porter cable ones and think they are Rockwell quality from before bought out. I burned out Makitas but never the Porter cable ones. dont...
  10. thats interesting but truck is a 72 so would it...

    thats interesting but truck is a 72 so would it still work then? will save that bit of info as never heard it before
  11. I looked at the solenoid and didnt see how its...

    I looked at the solenoid and didnt see how its removed. I have another starter from a 70 350 but it is different mounting system. Ill go the old school guy tomorrow and hope its still him that owns...
  12. thanks nok clilcking with 12 volts to that small...

    thanks nok clilcking with 12 volts to that small terminal, Told the other terminal is for points and this one has electronic on it. Do have an awesome old school rebuilder in a small down close by....
  13. starter motor experts 72 400 smal block

    For the first time in 18 years truck would not start. Tapped the starter with a hammer and started instantly as it always does. Worked fine for a day then today didnt so did the tap routine and no...
  14. Replies
    50
    Views
    3,001

    this is what I meant by combining machines so one...

    this is what I meant by combining machines so one becomes the outfeed and support for another. Rail on the SCM saw likely 54 inch or so rip capacity. Ive built tops over 50" before so not sure i...
  15. Replies
    50
    Views
    3,001

    paid less for a good used slider than an...

    paid less for a good used slider than an Exaclibur sliding table woud cost. Saw is 1,300 lbs and five ways better than a cabinet saw including up to a 16" blade max, 14" with scoring, 3 speeds and...
  16. I ended up needing to shim the infeed table on...

    I ended up needing to shim the infeed table on both sides. Just held the shims on with tape. I also was able to rotate the infeed a bit forward on the operator side. I didnt understand worm...
  17. biggest thing in a small shop is your machine...

    biggest thing in a small shop is your machine layout and type of work you will do. My first shop was likely not more than 300 feet and had 11 machines including two cabinet saws. Best thing is to...
  18. yeah not sure about stretching as was told not to...

    yeah not sure about stretching as was told not to them told them its too short. No one comments on the right hand side 1" extension in the channel. Whirlpool didnt help and ive sent it to two techs...
  19. Replies
    11
    Views
    927

    for Kitchens the old guys had a lot fewer joints....

    for Kitchens the old guys had a lot fewer joints. They built furniture as long as it made sense for moving and getting it in. Does put more stress on a face frame at some point. Now its a gaggle of...
  20. Replies
    4
    Views
    457

    Big difference there. be nice if that also...

    Big difference there. be nice if that also worked for all the brown aluminum doors that turn pink over time.
  21. maytag older dishwasher door gasket logic

    Need some logic on replacing this dishwasher door gasket on my parents Dishwasher. Took the bottom off and watched for a leak and 98 percent sure its the door gasket. Machine is older Maytag black...
  22. Replies
    25
    Views
    1,147

    ones I use are 75182. Sounds like a chicago...

    ones I use are 75182. Sounds like a chicago song.

    I have three and the plunge same size. The three were tortured for many years and still on the original bearings and work fine. Had read...
  23. id say the real issue is that it stays flat and...

    id say the real issue is that it stays flat and not stability unless you meant flat by stability. Cross grain expansion should make zero difference if a bench is designed right and mine are not, ...
  24. its a work bench not a piece of furniture. My...

    its a work bench not a piece of furniture. My ulmia benches one especially are beat to crap, so what. I had no issues machining IPE. I dont like the dust and it sticks to everything like it has a...
  25. Replies
    48
    Views
    3,704

    lamello the same. Even bought a new one just in...

    lamello the same. Even bought a new one just in case. Then the biscuits they are a whole other story.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4